Refer to DTC C110000.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| P05DB00 | Brake Pedal Position Sensor "B" | The difference in the SKS1 and SKS2 brake pedal stroke sensor assembly is invalid for 0.2 seconds or more. | ·
Wire harness and connector ·
Brake pedal stroke sensor assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
| P05E000 | Brake Pedal Position Sensor "A"/"B" | The difference in change between sensor output voltage 1 (SKS1) and sensor output voltage 2 (SKS2) is excessively large for 0.2 seconds or more. | ·
Wire harness and connector ·
Brake pedal stroke sensor assembly |
Output ECU: No. 2 skid control ECU (brake actuator assembly) |
Refer to DTC C110000.
After replacing or reinstalling the brake pedal stroke sensor assembly, perform "Calibration".
Mount a pedal effort gauge.
Turn the ignition switch to ON (READY) and depress the brake pedal once.
Depress the brake pedal after turning the ignition switch to ON (READY) to set the vehicle to linear mode (switching solenoid (SSA) on).
Depress the brake pedal slowly and check the brake pedal stroke sensor assembly output voltages with respect to brake pedal depression force.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor | Brake pedal stroke sensor 1 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 0.6 to 1.4 V | Reading increases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stroke Sensor2 | Brake pedal stroke sensor 2 | Min.: 0.0 V
Max.: 5.0 V |
Brake pedal released: 3.6 to 4.4 V | Reading decreases when brake pedal is depressed |
| Tester Display |
|---|
| Stroke Sensor2 |
Perform this procedure in linear mode (switching solenoid (SSA) on).
| Brake Effort
[N (kgf, lbf)] |
Stroke Sensor
[V] |
Stroke Sensor2
[V] |
|---|---|---|
| 50 (5, 11.2) | 1.20 to 1.90 | 3.10 to 3.80 |
| 100 (10, 22.5) | 1.42 to 2.16 | 2.88 to 3.58 |
| 150 (15, 33.7) | 1.61 to 2.31 | 2.69 to 3.39 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (brake pedal stroke sensor 1) | B |
| NG (brake pedal stroke sensor 2) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A44 No. 1 skid control ECU (brake booster with master cylinder assembly) connector.
Disconnect the A43 brake pedal stroke sensor assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A44-3 (SKS1) - A43-6 (SKS1) | Always | Below 1 Ω |
| A44-3 (SKS1) or A43-6 (SKS1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
The connector is securely connected.
Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.
Disconnect the A43 brake pedal stroke sensor assembly connector.
Check both the connector case and the terminals for deformation and corrosion.
No deformation or corrosion.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A57-10 (SKS2) - A43-1 (SKS2) | Always | Below 1 Ω |
| A57-10 (SKS2) or A43-1 (SKS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG