Home › Drivetrain › GF2A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM
RM37A0E _52 Drivetrain _086861 GF2A TRANSFER / 4WD / AWD _0421155 DYNAMIC TORQUE CONTROL AWD SYSTEM J

GF2A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  AWD Warning Remains ON  


DESCRIPTION

The 4WD ECU assembly is connected to the combination meter assembly via CAN communication.

If the 4WD ECU assembly stores any DTCs which are related to the dynamic torque control AWD system, the warning message is displayed on the multi-information display in the combination meter assembly.

WIRING DIAGRAM

C415810E03
0.531,1.51 2.427,1.854 1.896,0.344 10 false Multi-information Display 0.417,2.458 2.708,2.656 2.292,0.198 10 false Combination Meter Assembly 0.813,4.219 3.177,4.479 2.365,0.26 10 false : CAN Communication System 3.948,1.99 4.979,2.354 1.031,0.365 10 false ECU-IG1 NO. 2 5.635,1.604 6.104,1.948 0.469,0.344 10 false 24 5.667,2.479 5.875,2.76 0.208,0.281 10 false 1 5.958,1.823 6.417,2.021 0.458,0.198 10 false IG1 5.948,2.708 6.406,2.906 0.458,0.198 10 false GND 5.583,1.813 6.042,2.01 0.458,0.198 10 false M41 5.698,3.156 7.063,3.677 1.365,0.521 10 false 4WD ECU Assembly 5.583,2.698 6.042,2.896 0.458,0.198 10 false M41 5.583,1.156 6.052,1.396 0.469,0.24 10 false M42 5.583,0.594 6.042,0.792 0.458,0.198 10 false M42 5.938,0.594 6.5,0.802 0.563,0.208 10 false CANH 5.938,1.167 6.396,1.365 0.458,0.198 10 false CANL 5.625,0.385 6.094,0.729 0.469,0.344 10 false 17 5.635,0.948 6.104,1.292 0.469,0.344 10 false 26 0.417,2.281 0.875,2.479 0.458,0.198 10 false H21 2.125,0.594 2.698,0.844 0.573,0.25 10 false CANH 2.156,1.156 2.615,1.354 0.458,0.198 10 false CANL 2.656,0.958 3.125,1.302 0.469,0.344 10 false 31 2.646,0.396 3.115,0.74 0.469,0.344 10 false 32

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>CALIBRATION



HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK VEHICLE CONTROL HISTORY (DYNAMIC TORQUE CONTROL AWD SYSTEM)
a.

Using the GTS, check for Vehicle Control History.

Chassis > Four Wheel Drive > Utility
Tester Display
Vehicle Control History (RoB)
50005 448 55
HINT:

If vehicle control history is stored when the dynamic torque control AWD system is suspended, the warning message is displayed.



Result:
Result Proceed to
There is no vehicle control history for when the dynamic torque control AWD system was suspended. A
There is vehicle control history for when the dynamic torque control AWD system was suspended. B



A

2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

PERFORM TROUBLESHOOTING AND REPAIR REGARDING VEHICLE CONTROL HISTORY

Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>VEHICLE CONTROL HISTORY

NOTICE:

After performing troubleshooting and repairing regarding vehicle control history, clear the vehicle control history.



2.CHECK IF 4WD ECU ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the 4WD ECU assembly connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C408010C10
1.51,0.063 1.927,0.313 0.417,0.25 2.521,1.531 2.833,0.833 2.833,0.833 3,0.833 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 3.042,0.771 3.375,1.052 0.333,0.281 10 false IG1 1.594,0.104 2.052,0.302 0.458,0.198 10 false M41
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the M41 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M41-24 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Disconnect the M41 4WD ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M41-1 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (AWD WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING GTS (AWD WARNING LIGHT)
a.

According to the display on the GTS, read the Data List.

Chassis > Four Wheel Drive > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
4WD Warning Light AWD warning (multi-information display) OFF / ON OFF: Warning off
ON: Warning on
-
Chassis > Four Wheel Drive > Data List
Tester Display
4WD Warning Light
50003 448 114

b.

Check the GTS display condition of the AWD warning light.


Result:
Result Proceed to
Display of the Data List remains OFF A
Display of the Data List remains ON B



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B