When the 4WD ECU assembly is replaced, before removing the 4WD ECU assembly, it is necessary to perform ECU Data Save to save the original 4WD ECU assembly information.
When the 4WD ECU assembly is replaced, it is necessary to perform ECU Data Write (when replacing 4WD ECU assembly).
When the rear 4WD linear solenoid (electro magnetic control coupling sub-assembly) is replaced, it is necessary to perform ECU Data Write (when replacing rear 4WD linear solenoid (electro magnetic control coupling sub-assembly)).
When the front 4WD linear solenoid (transfer assembly) or rear 4WD linear solenoid (rear differential carrier assembly) is replaced, it is necessary to perform the following in order: ECU Data Initialization and Disconnect System Function Check.
When the temperature sensor is replaced, it is necessary to perform ECU Data Initialization.
| Replaced Part | Necessary Procedure |
|---|---|
| 4WD ECU assembly | 1.
ECU Data Save (ECU being replaced) 2.
ECU Data Write (When replacing 4WD ECU assembly) (New ECU) |
| Rear 4WD linear solenoid RH (electro magnetic control coupling sub-assembly RH) | 1.
ECU Data Write (When replacing rear 4WD linear solenoid RH (electro magnetic control coupling sub-assembly RH)) |
| Rear 4WD linear solenoid LH (electro magnetic control coupling sub-assembly LH) | 1.
ECU Data Write (When replacing rear 4WD linear solenoid LH (electro magnetic control coupling sub-assembly LH)) |
| Front 4WD linear solenoid (transfer assembly) | 1.
ECU Data Initialization 2.
Disconnect System Function Check |
| Rear 4WD linear solenoid (rear differential carrier assembly) | 1.
ECU Data Initialization 2.
Disconnect System Function Check |
| Temperature sensor | 1.
ECU Data Initialization |
| Tire | 1.
ECU Data Initialization (When performing tire replacement after RoB code X2104 is output) |
ECU DATA SAVE
| *1 | Rear 4WD Linear Solenoid LH (Electro Magnetic Control Coupling Sub-assembly LH) Compensation Code Label |
| *1 | Rear 4WD Linear Solenoid RH (Electro Magnetic Control Coupling Sub-assembly RH) Compensation Code Label |
According to the display on the GTS, perform ECU Data Save.
| Tester Display |
|---|
| ECU Data Save |
If the compensation code cannot be read, record the compensation code (4 digits in 8 blocks) on the electro magnetic control coupling sub-assembly compensation code label.
ECU DATA INITIALIZATION
According to the display on the GTS, perform ECU Data Initialization.
| Tester Display |
|---|
| ECU Data Initialization |
ECU DATA WRITE (WHEN REPLACING REAR 4WD LINEAR SOLENOID (ELECTRO MAGNETIC CONTROL COUPLING SUB-ASSEMBLY))
| *1 | Rear 4WD Linear Solenoid LH (Electro Magnetic Control Coupling Sub-assembly LH) Compensation Code Label |
| *1 | Rear 4WD Linear Solenoid RH (Electro Magnetic Control Coupling Sub-assembly RH) Compensation Code Label |
Record the printed compensation code (4 digits in 8 blocks) of a new rear 4WD linear solenoid (electro magnetic control coupling sub-assembly).
According to the display on the GTS, perform ECU Data Write.
| Tester Display |
|---|
| ECU Data Write |
Using the on-screen buttons, input the compensation code.
According to the display on the GTS, complete work.
ECU DATA WRITE (WHEN REPLACING 4WD ECU ASSEMBLY)
According to the display on the GTS, perform ECU Data Write.
| Tester Display |
|---|
| ECU Data Write |
DISCONNECT SYSTEM FUNCTION CHECK
Perform this work with 4 or more people as the tires need to be rotated by hand when working.
According to the display on the GTS, perform Disconnect System Function Check.
| Tester Display |
|---|
| Disconnect System Function Check |
Do not hold the inside of the wheel when rotating the tire, as doing so could pinch your fingers.
If disconnect switching fails, perform the same procedure. If it fails again, inspect the part.
When replacing the front 4WD linear solenoid (transfer assembly):
Click hereDrivetrain>GF2A (TRANSFER / 4WD / AWD)>TRANSFER ASSEMBLY>INSTALLATION
When replacing the rear 4WD linear solenoid (rear differential carrier assembly):