Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › REAR DRIVE SHAFT ASSEMBLY (for 2GR-FKS)
RM37A0E _52 Drivetrain _086862 DRIVE SHAFT / PROPELLER SHAFT _0421215 REAR DRIVE SHAFT ASSEMBLY(for 2GR-FKS) A

DRIVE SHAFT / PROPELLER SHAFT  REAR DRIVE SHAFT ASSEMBLY(for 2GR-FKS)  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT

a.
C166359C04
1.917,0.885 2.427,0.375 2.427,0.375 2.792,0.375 false 2.823,0.281 3.177,0.49 0.354,0.208 10 *a
*a Protective Tape


Wrap the splines of the rear drive shaft outboard joint shaft assembly with protective tape to prevent the boot from being damaged.


b.
C274280C01
1.115,1.719 1.115,1.427 false 1.656,1.74 1.656,1.479 false 2.344,1.74 2.344,1.438 false 2.979,1.75 2.979,1.229 false 1.063,1.781 1.375,1.938 0.313,0.156 10 *1 1.604,1.792 1.917,1.948 0.313,0.156 10 *2 2.281,1.781 2.594,1.938 0.313,0.156 10 *3 2.948,1.792 3.26,1.948 0.313,0.156 10 *4
*1 Rear Drive Shaft Outboard Joint Shaft Assembly
*2 Rear No. 2 Drive Shaft Outboard Joint Boot Clamp
*3 Rear Drive Shaft Outboard Joint Boot
*4 Rear Drive Shaft Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

i.

Rear No. 2 drive shaft outboard joint boot clamp


ii.

Rear drive shaft outboard joint boot


iii.

Rear drive shaft outboard joint boot clamp



c.

Pack the joint portion of the rear drive shaft outboard joint shaft assembly and rear drive shaft outboard joint boot with grease.

Standard Grease Capacity:
for Dynamic Torque Vectoring AWD 68 to 78 g (2.40 to 2.75 oz)
for Dynamic Torque Control AWD 50 to 60 g (1.77 to 2.11 oz.)



d.

Install the rear drive shaft outboard joint boot to the rear drive shaft outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 42346F 2.INSTALL REAR NO. 2 DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

for Type A:

i.
C277141

Using a screwdriver, install the rear No. 2 drive shaft outboard joint boot clamp as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft outboard joint boot.




c.

for Type B:

i.

Install the rear No. 2 drive shaft outboard joint boot clamp to the rear drive shaft outboard joint boot.


ii.
C285537C04
0.708,0.646 1.469,1.021 false 2.656,0.594 2.969,0.792 0.313,0.198 10 false *a 1.219,0.292 1.531,0.49 0.313,0.198 10 false *b 0.427,0.552 0.885,0.75 0.458,0.198 10 false SST
*a Turn
*b Hold


Place SST onto the rear No. 2 drive shaft outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the rear No. 2 drive shaft outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.
C106165N13
2.031,1.031 2.698,1.844 false 2.646,1.865 3.094,2.104 0.448,0.24 10 SST

Using SST, measure the clearance of the rear No. 2 drive shaft outboard joint boot clamp.

SST
09240-00021  

Clearance:

0 to 2.1 mm (0 to 0.0827 in.)


If the clearance is not as specified, retighten SST.



Hide 42346D 3.INSTALL REAR DRIVE SHAFT OUTBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Install the rear drive shaft outboard joint boot clamp to the rear drive shaft outboard joint boot.


c.
C277142C06
1.115,1.75 1.521,1.75 1.521,1.75 2,1.208 true 0.833,1.677 1.292,1.875 0.458,0.198 10 false SST 1.448,0.115 1.906,0.313 0.458,0.198 10 false *b 2.25,1.781 2.708,1.979 0.458,0.198 10 false *a
*a Turn
*b Hold


Place SST onto the rear drive shaft outboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


d.

Tighten SST so that the rear drive shaft outboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



e.

Remove SST.


f.
C277143N02
1.656,1.5 2.365,1.5 true 2.438,1.417 2.896,1.615 0.458,0.198 10 false SST

Using SST, measure the clearance of the rear drive shaft outboard joint boot clamp.

SST
09240-00021  

Clearance:
for Dynamic Torque Vectoring AWD 0 to 1.3 mm (0 to 0.0512 in.)
for Dynamic Torque Control AWD 0 to 1.2 mm (0 to 0.0472 in.)


If the clearance is not as specified, retighten SST.


Hide 4.INSTALL REAR DRIVE SHAFT INBOARD JOINT ASSEMBLY

a.
C274277C02
0.688,1.875 0.688,1.333 false 1.698,1.854 1.698,1.615 false 2.49,1.875 2.49,1.667 false 2.927,1.885 2.927,1.25 false 0.625,1.896 0.938,2.052 0.313,0.156 10 *1 1.635,1.896 1.948,2.052 0.313,0.156 10 *2 2.417,1.906 2.729,2.063 0.313,0.156 10 *3 2.875,1.896 3.188,2.052 0.313,0.156 10 *a
*1 Rear Drive Shaft Inboard Joint Boot Clamp
*2 Rear Drive Shaft Inboard Joint Boot
*3 Rear No. 2 Drive Shaft Inboard Joint Boot Clamp
*a Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side


Install new parts to the rear drive shaft outboard joint shaft assembly in the following order:

i.

Rear drive shaft inboard joint boot clamp


ii.

Rear drive shaft inboard joint boot


iii.

Rear No. 2 drive shaft inboard joint boot clamp



b.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C157561C03
1.542,1.615 2.354,1.781 2.354,1.781 2.073,1.281 false 2.396,1.719 2.594,1.885 0.198,0.167 10 *a
*a Matchmark


Align the matchmarks and install the tripod joint to the rear drive shaft outboard joint shaft assembly.

NOTICE:

Face the serrated side of the tripod joint outward and install it to the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the rear drive shaft outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.

·

Be sure to install the tripod joint in the correct direction.




f.
C160822

Using a snap ring expander, install a new shaft snap ring to the rear drive shaft outboard joint shaft assembly.


g.

Pack the rear drive shaft inboard joint assembly and rear drive shaft inboard joint boot with grease.

Standard Grease Capacity:
for Dynamic Torque Vectoring AWD 134 to 144 g (4.73 to 5.08 oz)
for Dynamic Torque Control AWD 93 to 103 g (3.29 to 3.63 oz)



h.
C160821C17
1.823,0.781 0.792,0.458 0.792,0.458 1.375,1.229 false 0.594,0.375 0.854,0.542 0.26,0.167 10 *a
*a Matchmark


Align the matchmarks and install the rear drive shaft inboard joint assembly to the rear drive shaft outboard joint shaft assembly.


Hide 5.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT

a.

Install the rear drive shaft inboard joint boot to the rear drive shaft inboard joint assembly.


b.
C157783N46
1.573,1.688 1.802,1.865 0.229,0.177 10 false A

Check whether the drive shaft dimension (A) is within specification.

Dimension (A):
for Dynamic Torque Vectoring AWD for LH Side 643.6 mm (2.11 ft.)
for RH Side 628.6 mm (2.06 ft.)
for Dynamic Torque Control AWD for LH Side 683.25 mm (2.24 ft.)
for RH Side 703.25 mm (2.31 ft.)



Hide 42347F 6.INSTALL REAR NO. 2 DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

for Type A:

i.
C429355C01
0.406,0.76 0.719,1.292 0.719,1.292 1.26,0.76 false 0.635,1.323 0.802,1.469 0.167,0.146 10 false *a
*a Claw


Using needle-nose pliers, engage the 2 claws to install the rear No. 2 drive shaft inboard joint boot clamp as shown in the illustration.



c.

for Type B:

HINT:

Perform the same procedure as for the rear No. 2 drive shaft outboard joint boot clamp.



Hide 42347D 7.INSTALL REAR DRIVE SHAFT INBOARD JOINT BOOT CLAMP

a.

Secure the drive shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C157519C03
0.66,1.511 0.825,1.653 0.165,0.141 10 *a 0.36,1.14 0.742,1.494 0.742,1.494 1.132,0.985 false
*a Claw


for Type A:

i.

Using needle-nose pliers, engage the 2 claws to install the rear drive shaft inboard joint boot clamp as shown in the illustration.

NOTICE:

Be careful not to damage the rear drive shaft inboard joint boot.




c.

for Type B:

i.

Install the rear drive shaft inboard joint boot clamp to the rear drive shaft inboard joint boot.


ii.
C296175C01
1.74,1.396 2.104,1.708 2.104,1.708 2.729,1.708 true 2.781,1.625 3.24,1.823 0.458,0.198 10 false SST 2.99,0.125 3.302,0.281 0.313,0.156 10 false *a 1.646,0.51 1.958,0.667 0.313,0.156 10 false *b
*a Turn
*b Hold


Place SST onto the rear drive shaft inboard joint boot clamp, press it against the boot and slightly tighten SST.

SST
09521-24010  


iii.

Tighten SST so that the rear drive shaft inboard joint boot clamp is pinched.

NOTICE:

Do not overtighten SST.



iv.

Remove SST.


v.
C195760N02
1.531,1.5 2.365,1.5 false 2.406,1.417 2.854,1.667 0.448,0.25 10 false SST

Using SST, measure the clearance of the rear drive shaft inboard joint boot clamp.

SST
09240-00021  

Clearance:

0 to 1.3 mm (0 to 0.0512 in.)


If the clearance is not as specified, retighten SST.