Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2020.02–2020.11
RM37A0E _58 Vehicle Interior _086892 SUPPLEMENTAL RESTRAINT SYSTEMS _0421220 STEERING PAD A

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during horn button assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

Disconnect cable from negative auxiliary battery terminal Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
B394719

Be sure to read Precaution thoroughly before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.


Hide 58441L 2.REMOVE BATTERY SERVICE HOLE COVER (for HV Model)

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for 2GR-FKS: Click hereGeneral>MAINTENANCE>2GR-FKS BATTERY>REMOVAL

for A25A-FXS, A25B-FXS: Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>REMOVAL

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 45187 4.REMOVE LOWER NO. 3 STEERING WHEEL COVER

a.
B528832C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, insert the screwdriver into the cutout of the lower No. 3 steering wheel cover and disengage the claw and guide to remove the lower No. 3 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



Hide 45186 5.REMOVE LOWER NO. 2 STEERING WHEEL COVER

a.
B528831C01
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, insert the screwdriver into the cutout of the lower No. 2 steering wheel cover and disengage the claw and guide to remove the lower No. 2 steering wheel cover.

HINT:

Tape the screwdriver tip before use.



Hide 45130 6.REMOVE HORN BUTTON ASSEMBLY

CAUTION:
B528833C01
0,0 0,0 false
V100155

Deployment Side


When storing the horn button assembly, keep the airbag deployment side facing upward.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B528834C05
0.302,0.74 0.521,0.74 true 2.917,0.729 3.115,0.729 true 2.635,2.917 2.635,3.115 true 0.125,0.646 0.323,0.844 0.198,0.198 10 true *a 3.125,0.635 3.323,0.833 0.198,0.198 10 true *a 2.542,3.115 2.74,3.313 0.198,0.198 10 true *a
*a Torsion Spring
V100135

Push in this Direction


Using a screwdriver, push in the 3 torsion springs to disengage the 3 pins as shown in the illustration.

NOTICE:

Lightly hold the horn button assembly so that it does not fall.


HINT:

Insert the screwdriver from the installation holes for the lower No. 3 steering wheel cover or lower No. 2 steering wheel cover.



d.

Pull out the horn button assembly from the steering wheel assembly and hold the horn button assembly with one hand.

NOTICE:

When separating the horn button assembly, do not pull the airbag wire harness.



e.
B566220C01
1.021,1 1.021,0.74 1.021,0.74 0.25,0.74 true 1.177,1.25 1.177,1.927 true 2.563,1.344 2.302,1.344 true 1.479,0.979 1.479,0.5 1.479,0.5 1.896,0.5 true 0.073,0.646 0.292,0.844 0.219,0.198 10 false *a 1.083,1.938 1.281,2.125 0.198,0.188 10 true *b 2.125,1.25 2.302,1.448 0.177,0.198 10 true *c 1.917,0.417 2.135,0.604 0.219,0.188 10 true *d
*a Airbag Connector
*b Horn Connector
*c Protective Tape
*d Wire Harness Clamp
V113147

Release in this Direction
V113148

Remove in this Direction


Disconnect the horn connector from the horn button assembly.


f.

Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.


HINT:

Refer to How to Connect or Disconnect Airbag Connector.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO CONNECT OR DISCONNECT AIRBAG CONNECTOR



g.

Using a screwdriver with its tip wrapped with protective tape, release the lock and remove the wire harness clamp to remove the horn button assembly.