A backup boost converter is built into the engine stop and start ECU.
The backup boost converter helps maintain battery voltage to prevent various functions from failing if power source voltage supplied from the backup boost converter drops due to the high electrical load when the engine is restarted by stop and start control.
The backup boost converter helps maintain the power source voltage if the battery voltage drops due to the high electrical load when the engine is restarted by stop and start control.
A relay function and fuse function are provided in the backup boost converter.
If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).
When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.
The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.
*: A semiconductor fuse self resets according to electric signal.
Electronically controlled brake system
Power steering system
Meter / gauge system
Audio and visual system
Navigation system
Rear seat entertainment system
Digital rear-view mirror system
Auto glare-resistant EC mirror
Lighting system (INT)
Air conditioning system
CAN communication system
Toyota safety sense
Parking support alert system
Headup display system
Blind spot monitor system
Fog light assembly
Navigation system
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory | Note |
|---|---|---|---|---|---|---|
| P323A19 | Backup Boost Converter "A" Circuit Current Above Threshold | The following condition continues for 1 second or more (1 trip detection logic):
·
Overcurrent is detected at the B41, B42, B43, IG41 and EMOP terminals in the engine stop and start ECU |
·
Wire harness or connector ·
Meter mirror assembly (w/ Headup Display) ·
Navigation ECU (w/ Navigation System) ·
Radio and display receiver assembly ·
Television display assembly (w/ Rear Seat Entertainment System) ·
Inner Rear View Mirror Assembly (w/ EC Mirror or Digital Inner Mirror) ·
Front door ambient light LH (front door trim board sub-assembly LH) (w/ Ambient Illumination Light) ·
Front door ambient light RH (front door trim board sub-assembly RH) (w/ Ambient Illumination Light) ·
Rear door ambient light LH (rear door trim board sub-assembly LH) (w/ Ambient Illumination Light) ·
Rear door ambient light RH (rear door trim board sub-assembly RH) (w/ Ambient Illumination Light) ·
Front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) (w/ Ambient Illumination Light) ·
Center tray illumination light (No. 1 instrument panel light sub-assembly) (w/ Ambient Illumination Light) ·
Blind spot monitor sensor LH ·
Blind spot monitor sensor RH ·
Millimeter wave radar sensor assembly ·
Clearance warning ECU assembly ·
Air conditioning control assembly ·
No. 2 air conditioning control assembly ·
Central gateway ECU (network gateway ECU) ·
Oil pump with solenoid assembly ·
Engine stop and start ECU |
Blinks | DTC stored | SAE Code: P323A |
CONFIRMATION AFTER TROUBLESHOOTING
If the cable is disconnected from the battery terminal, stop and start control is prohibited until refresh charge is completed.
In this case, let the vehicle idle to complete the refresh charge. The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode". (Usually, idling the engine for 5 to 60 minutes with the battery fluid temperature at 11°C (52°F) or higher, the refresh charge will be completed.)
If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.
If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.
After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again. If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.
Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Start the engine and warm it up.
Drive the vehicle at 7 km/h (4 mph) or more.
When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.
Depress the brake pedal and stop the vehicle.
Keep the engine stopped by stop and start control for 1 second or more. (Keep the shift lever in D.)
Release the brake pedal with the shift lever in D to start the engine.
If the engine cranks slowly when the engine is restarted, it can be determined that the battery voltage is low.
Check that DTCs are not output.
STOP AND START SYSTEM OPERATION CHECK
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the engine stop and start ECU or oil pump with solenoid assembly is replaced, check the oil pump with solenoid assembly.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If electrical load from additional devices installed to the vehicle (aftermarket audio system, etc.) is applied to the B41, B42, B43, IG41 or EMOP terminal in the engine stop and start ECU, the fuse function of the backup boost converter may operate.
If the fuse function of the backup boost converter operates, any systems connected to the B41, B42, B43, IG41 or EMOP terminal in the engine stop and start ECU will not operate.
If DTCs P279612 (Electromagnetic Oil Pump Circuit Short to Battery), P279614 (Electromagnetic Oil Pump Circuit Open), P279796 (Electromagnetic Oil Pump Component Internal Failure) and P323A19 (Backup Boost Converter "A" Circuit Current Above Threshold) are output simultaneously, troubleshoot for DTC P279612, P279614 or P279796 first, as a malfunction which causes DTC P279612, P279614 or P279796 to be stored may also cause DTC P323A19 to be stored.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR
Using the GTS, read the Freeze Frame Data before troubleshooting. System condition information is recorded as Freeze Frame Data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P323A19 is output | A |
| DTC P279612, P279614 or P279796 and P323A19 are output | B |
If DTCs P323A19 and P279612, P279614 or P279796 are output simultaneously, troubleshoot for DTC P279612, P279614 or P279796 first.
A
B
Disconnect the engine stop and start ECU connector.
Remove the BBC NO. 1 fuse and BBC NO. 2 fuse from the No. 1 engine room relay block and No. 1 junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A33-1 (BIN2) - 2 (BBC NO. 2 fuse) | Always | Below 1 Ω |
| A33-3 (BIN1) - 2 (BBC NO. 1 fuse) | Always | Below 1 Ω |
| A33-1 (BIN2) or 2 (BBC NO. 2 fuse) - Body ground and other terminals | Always | 10 kΩ or higher |
| A33-3 (BIN1) or 2 (BBC NO. 1 fuse) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the engine stop and start ECU connector.
Remove the FOG FR relay from the No. 1 engine room relay block and No. 1 junction block assembly.
Disconnect the navigation ECU connector. (w/ Navigation System)
Disconnect the meter mirror assembly connector. (w/ Headup Display)
Disconnect the radio and display receiver assembly connector.
Disconnect the television display assembly connector. (w/ Rear Seat Entertainment System)
Disconnect the inner rear view mirror assembly connector. (w/ EC Mirror or Digital Inner Mirror)
Disconnect the front door ambient light LH (front door trim board sub-assembly LH) connector. (w/ Ambient Illumination Light)
Disconnect the front door ambient light RH (front door trim board sub-assembly RH) connector. (w/ Ambient Illumination Light)
Disconnect the rear door ambient light LH (rear door trim board sub-assembly LH) connector. (w/ Ambient Illumination Light)
Disconnect the rear door ambient light RH (rear door trim board sub-assembly RH) connector. (w/ Ambient Illumination Light)
Disconnect the front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) connector. (w/ Ambient Illumination Light)
Disconnect the center tray illumination light (No. 1 instrument panel light sub-assembly) connector. (w/ Ambient Illumination Light)
Disconnect the air conditioning control assembly connector.
Disconnect the central gateway ECU (network gateway ECU) connector.
Disconnect the millimeter wave radar sensor assembly connector.
Disconnect the clearance warning ECU assembly connector.
Disconnect the blind spot monitor sensor LH connector.
Disconnect the blind spot monitor sensor RH connector.
Disconnect the No. 2 air conditioning control assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-2 (B41) - 2 (FOG FR relay) | Always | Below 1 Ω |
| H66-2 (B41) - 5 (FOG FR relay) | Always | Below 1 Ω |
| H66-2 (B41) - H18-10 (+B)*1 | Always | Below 1 Ω |
| H66-2 (B41) - H31-2 (B)*2 | Always | Below 1 Ω |
| H66-12 (B42) - H1-4 (+B1) | Always | Below 1 Ω |
| H66-11 (B43) - R16-1 (+B)*3 | Always | Below 1 Ω |
| H66-11 (B43) -J26-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -J10-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -K10-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -K5-2 (+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -H69-2 (ILL+)*5 | Always | Below 1 Ω |
| H66-11 (B43) -H68-2 (ILL+)*5 | Always | Below 1 Ω |
| H66-3 (IG41) - R1-1 (IG)*4 | Always | Below 1 Ω |
| H66-3 (IG41) - H31-1 (IG)*2 | Always | Below 1 Ω |
| H66-3 (IG41) - H27-6 (IG+) | Always | Below 1 Ω |
| H66-3 (IG41) - H59-11 (IG1) | Always | Below 1 Ω |
| H66-3 (IG41) - B6-8 (IGB) | Always | Below 1 Ω |
| H66-3 (IG41) - H46-1 (IG) | Always | Below 1 Ω |
| H66-3 (IG41) - M43-5 (BLB) | Always | Below 1 Ω |
| H66-3 (IG41) - M2-5 (BRB) | Always | Below 1 Ω |
| H66-3 (IG41) - T2-9 (IG) | Always | Below 1 Ω |
| H66-2 (B41) or 2 (FOG FR relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or 5 (FOG FR relay) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or H18-10 (+B)*1 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-2 (B41) or H31-2 (B)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-12 (B42) or H1-4 (+B1) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or R16-1 (+B)*3 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or J26-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or J10-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or K10-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or K5-2 (+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or H69-2 (ILL+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-11 (B43) or H68-2 (ILL+)*5 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or R1-1 (IG)*4 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H31-1 (IG)*2 - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H27-6 (IG+) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H59-11 (IG1) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or B6-8 (IGB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or H46-1 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or M43-5 (BLB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or M2-5 (BRB) - Body ground and other terminals | Always | 10 kΩ or higher |
| H66-3 (IG41) or T2-9 (IG) - Body ground and other terminals | Always | 10 kΩ or higher |
*1: w/ Navigation System
*2: w/ Headup Display
*3: w/ Rear Seat Entertainment System
*4: w/ EC Mirror or Digital Inner Mirror
*5: w/ Ambient Illumination Light
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Engine Stop and Start ECU) |
- | - |
Disconnect the engine stop and start ECU connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H66-2 (B41) - A34-6 (DGND) | Always | 10 kΩ or higher |
| H66-3 (IG41) - A34-6 (DGND) | Always | 10 kΩ or higher |
| H66-11 (B43) - A34-6 (DGND) | Always | 10 kΩ or higher |
| H66-12 (B42) - A34-6 (DGND) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check that additional devices installed to the vehicle (aftermarket audio system, etc.) are not connected to the B41, B42, B43 or IG41 terminal circuit of the engine stop and start ECU.
| Result | Proceed to |
|---|---|
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is not applied. | A |
| Load from an additional device installed to the vehicle (aftermarket audio system, etc.) is applied. | B |
A
B