Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  B1574  GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device)  


DESCRIPTION

The multi-display assembly and parking assist ECU are connected via video signal (digital) lines.

This DTC is stored when a video signal (digital) line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1574 GVIF Disconnected (from Park Assist/Monitoring ECU to EMV/MM Integrated Device) GVIF disconnected (from parking assist ECU to multi-display assembly)
·

Harness or connector (GVIF cable)

·

Multi-display assembly

·

Parking assist ECU



WIRING DIAGRAM

E381479E73
1.208,3.125 2.646,3.448 1.438,0.323 10 false : GVIF Cable 1.271,2.333 1.771,2.552 0.5,0.219 10 false H104 1.281,2.5 2.844,2.719 1.563,0.219 10 false Multi-display Assembly 2.177,0.823 2.677,1.042 0.5,0.219 10 false GV+ 2.146,1.969 2.646,2.188 0.5,0.219 10 false GND 4.917,2.344 5.417,2.563 0.5,0.219 10 false H103 4.917,2.5 6.594,2.74 1.677,0.24 10 false Parking Assist ECU 4.875,1.229 5.375,1.448 0.5,0.219 10 false 2 4.885,0.667 5.385,0.885 0.5,0.219 10 false 1 4.865,1.865 5.365,2.083 0.5,0.219 10 false 3 2.177,1.365 2.677,1.583 0.5,0.219 10 false GV- 5.063,1.969 5.563,2.188 0.5,0.219 10 false GND 2.552,0.688 3.052,0.906 0.5,0.219 10 false 1 2.552,1.24 3.052,1.458 0.5,0.219 10 false 2 2.583,1.833 3.083,2.052 0.5,0.219 10 false 3 5.073,1.365 5.573,1.583 0.5,0.219 10 false GV- 5.063,0.823 5.563,1.042 0.5,0.219 10 false GV+ 3.729,1.823 4.229,2.042 0.5,0.219 10 false * 5.208,3.219 6.885,3.458 1.677,0.24 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION


PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - PARKING ASSIST ECU)
2.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - PARKING ASSIST ECU)
a.
E429902C01
1.5,0.667 1.917,0.917 0.417,0.25 1.5,2.917 1.917,3.167 0.417,0.25 1.771,1.5 2.188,1.146 2.188,1.146 2.344,1.146 true 1.771,3.635 2.188,3.281 2.188,3.281 2.344,3.281 true 1.063,3.302 1.219,3.302 1.219,3.302 1.635,3.625 true 1.042,1.177 1.198,1.177 1.198,1.177 1.615,1.5 true 1.74,1.656 1.99,2.125 1.99,2.125 2.146,2.125 true 1.729,3.771 1.979,4.24 1.979,4.24 2.135,4.24 true 0.75,0.479 1.063,0.677 0.313,0.198 10 false *a 0.729,2.74 1.042,2.938 0.313,0.198 10 false *b 1.552,2.969 2.167,3.167 0.615,0.198 10 false H103 1.552,0.708 2.167,0.906 0.615,0.198 10 false H104 0.677,1.115 1.448,1.313 0.771,0.198 10 false GV+ 0.719,3.219 1.49,3.417 0.771,0.198 10 false GV+ 2.396,1.063 3.167,1.26 0.771,0.198 10 false GV- 2.385,3.208 3.156,3.406 0.771,0.198 10 false GV- 2.198,2.031 2.969,2.229 0.771,0.198 10 false GND 2.188,4.156 2.958,4.354 0.771,0.198 10 false GND
*a Front view of wire harness connector
(to Multi-display Assembly)
*b Front view of wire harness connector
(to Parking Assist ECU)


Disconnect the H104 multi-display assembly connector.


b.

Disconnect the H103 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H104-2 (GV-) - H103-2 (GV-) Always Below 1 Ω
H104-1 (GV+) - H103-1 (GV+) Always Below 1 Ω
H104-3 (GND) - H103-3 (GND) Always Below 1 Ω
H104-2 (GV-) or H103-2 (GV-) - Body ground Always 10 kΩ or higher
H104-1 (GV+) or H103-1 (GV+) - Body ground Always 10 kΩ or higher
H104-3 (GND) or H103-3 (GND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Change the shift position to R and check for DTCs.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

NG