Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  B15D6  Display Disconnected  


DESCRIPTION

The integration control sub-assembly and radio receiver assembly are connected by AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the integration control sub-assembly and radio receiver assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D6 Display Disconnected A device that is listed in the AVC-LAN connected device record of the master unit is missing
·

Integration control sub-assembly power source circuit

·

AVC-LAN circuit between radio receiver assembly and integration control sub-assembly

·

Integration control sub-assembly

·

Radio receiver assembly

·

Harness or connector



HINT:

The radio receiver assembly is the master unit.


WIRING DIAGRAM

E442352E08
0.135,0.75 3.5,0.948 3.365,0.198 10 false from Auxiliary Battery 0.115,2.042 3.479,2.24 3.365,0.198 10 false from IG1-NO. 1 Relay 0.448,1.406 3.813,1.604 3.365,0.198 10 false from ACC Relay 2.104,0.938 3.177,1.177 1.073,0.24 10 false ECU-B NO. 2 2.052,2.198 3.125,2.438 1.073,0.24 10 false ECU-IG1 NO. 4 2.198,1.573 3.271,1.813 1.073,0.24 10 false ECU-ACC 3.5,2.042 4.573,2.281 1.073,0.24 10 false IG+ 3.51,0.76 4.583,1 1.073,0.24 10 false B 3.51,1.417 4.583,1.656 1.073,0.24 10 false ACC 4.052,2.052 5.125,2.292 1.073,0.24 10 false GND 4.052,1.406 5.125,1.646 1.073,0.24 10 false TX1- 4.042,0.76 5.115,1 1.073,0.24 10 false TX1+ 5.813,0.75 6.885,0.99 1.073,0.24 10 false TX4+ 5.823,1.385 6.896,1.625 1.073,0.24 10 false TX4- 5.563,0.604 6.635,0.844 1.073,0.24 10 false 17 5.563,1.26 6.635,1.5 1.073,0.24 10 false 18 4.458,0.604 5.531,0.844 1.073,0.24 10 false 36 4.438,1.25 5.51,1.49 1.073,0.24 10 false 35 4.448,1.927 5.521,2.167 1.073,0.24 10 false 20 3.302,0.615 4.375,0.854 1.073,0.24 10 false 1 3.313,1.927 4.385,2.167 1.073,0.24 10 false 4 3.302,1.292 4.375,1.531 1.073,0.24 10 false 3 0.813,3.344 4.177,3.542 3.365,0.198 10 false : AVC-LAN Communication Line 2.896,2.771 3.969,3.01 1.073,0.24 10 false H8 2.896,2.927 5.167,3.177 2.271,0.25 10 false Integration Control Sub-assembly 5.406,2.75 6.479,2.99 1.073,0.24 10 false H6 5.406,2.927 7.052,3.188 1.646,0.26 10 false Radio Receiver Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B



A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY POWER SOURCE)
a.

Disconnect the H8 integration control sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-20 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-1 (B) - H8-20 (GND) Ignition switch off 11 to 14 V
H8-3 (ACC) - H8-20 (GND) Ignition switch ACC 11 to 14 V
H8-4 (IG+) - H8-20 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT RADIO RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RADIO RECEIVER ASSEMBLY
a.
E367494C82
1.542,0.75 1.958,1.021 0.417,0.271 2.917,2.792 2.677,2.229 false 2.292,2.771 2.5,2.198 false 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.667,0.802 1.979,1 0.313,0.198 10 false H6 2.781,2.854 3.208,3.083 0.427,0.229 10 false TX4+ 2.146,2.844 2.76,3.042 0.615,0.198 10 false TX4-
*a Component without harness connected
(Radio Receiver Assembly)


Disconnect the H6 radio receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
17 (TX4+) - 18 (TX4-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)

NG

REPLACE RADIO RECEIVER ASSEMBLY

6.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
a.

Disconnect the H6 radio receiver assembly connector.


b.

Disconnect the H8 integration control sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-17 (TX4+) - H8-36 (TX1+) Always Below 1 Ω
H6-18 (TX4-) - H8-35 (TX1-) Always Below 1 Ω
H6-17 (TX4+) or H8-36 (TX1+) - Body ground Always 10 kΩ or higher
H6-18 (TX4-) or H8-35 (TX1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE INTEGRATION CONTROL SUB-ASSEMBLY
a.

Replace the integration control sub-assembly with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO RECEIVER ASSEMBLY