Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  AVC-LAN Circuit  


DESCRIPTION

Each unit of the navigation system connected to the AVC-LAN (communication bus) transmits switch signals via AVC-LAN communication.

If a short to +B or short to ground occurs in the AVC-LAN, the navigation system will not function normally because communication is not possible.

WIRING DIAGRAM

E323016E10
0.906,3.396 2.958,3.615 2.052,0.219 10 false : AVC-LAN Communication Line 1.385,1.271 3.167,1.646 1.781,0.375 10 false Radio Receiver Assembly 4.667,2.781 4.99,2.99 0.323,0.208 10 false H8 1.396,1.104 1.76,1.323 0.365,0.219 10 false H6 4.667,2.927 6.938,3.188 2.271,0.26 10 false Integration Control Sub-assembly 1.448,2.729 1.771,2.938 0.323,0.208 10 false H7 1.438,2.906 3.396,3.198 1.958,0.292 10 false Multi-display Assembly 5.24,0.323 5.854,0.521 0.615,0.198 10 false TX1+ 5.24,0.719 5.854,0.917 0.615,0.198 10 false TX1- 5.24,2.021 5.854,2.219 0.615,0.198 10 false TX+ 5.25,2.417 5.865,2.615 0.615,0.198 10 false TX- 4.958,0.188 5.281,0.396 0.323,0.208 10 false 36 4.958,0.583 5.281,0.792 0.323,0.208 10 false 35 4.969,1.875 5.292,2.083 0.323,0.208 10 false 18 4.969,2.271 5.292,2.479 0.323,0.208 10 false 40 2.719,0.188 3.042,0.396 0.323,0.208 10 false 17 2.719,0.594 3.042,0.802 0.323,0.208 10 false 18 2.719,1.885 3.042,2.094 0.323,0.208 10 false 7 2.719,2.281 3.042,2.49 0.323,0.208 10 false 19 2.302,0.313 2.677,0.51 0.375,0.198 10 false TX4+ 2.333,0.698 2.708,0.896 0.375,0.198 10 false TX4- 2.385,2 2.76,2.198 0.375,0.198 10 false TX+ 2.417,2.385 2.792,2.583 0.375,0.198 10 false TX-

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>PRECAUTION


HINT:

The radio receiver assembly is the master unit.


PROCEDURE

1.INSPECT RADIO RECEIVER ASSEMBLY
a.

Remove the radio receiver assembly.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER>REMOVAL


b.
E367494C84
1.542,0.75 1.958,1.021 0.417,0.271 2.917,2.792 2.677,2.229 false 2.292,2.771 2.5,2.198 false 0.229,0.177 0.542,0.375 0.313,0.198 10 false *a 1.667,0.802 1.979,1 0.313,0.198 10 false H6 2.781,2.854 3.208,3.083 0.427,0.229 10 false TX4+ 2.146,2.844 2.76,3.042 0.615,0.198 10 false TX4-
*a Component without harness connected
(Radio Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-17 (TX4+) - H6-18 (TX4-) Always 60 to 80 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)

NG

REPLACE RADIO RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)
a.

Disconnect the H6 radio receiver assembly connector.


b.

Disconnect the H8 integration control sub-assembly connector.


c.

Disconnect the H7 multi-display assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H6-17 (TX4+) - H8-36 (TX1+) Always Below 1 Ω
H6-18 (TX4-) - H8-35 (TX1-) Always Below 1 Ω
H6-17 (TX4+) or H8-36 (TX1+) - Body ground Always 10 kΩ or higher
H6-18 (TX4-) or H8-35 (TX1-) - Body ground Always 10 kΩ or higher
H8-18 (TX+) - H7-7 (TX+) Always Below 1 Ω
H8-40 (TX-) - H7-19 (TX-) Always Below 1 Ω
H8-18 (TX+) or H7-7 (TX+) - Body ground Always 10 kΩ or higher
H8-40 (TX-) or H7-19 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MALFUNCTIONING PARTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MALFUNCTIONING PARTS
a.

Disconnect and reconnect each slave unit one by one until the master unit returns to normal.

HINT:
·

Check all slave units.

·

If disconnecting a slave unit causes the master unit to return to normal, the slave unit is defective and should be replaced.



OK:

Master unit return to normal.



Result:
Proceed to
OK
NG



OK

REPLACE MALFUNCTIONING PARTS

NG

REPLACE RADIO RECEIVER ASSEMBLY