Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 12.3 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0444619 NAVIGATION SYSTEM(for 12.3 Inch Display) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 12.3 Inch Display)  Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter  


DESCRIPTION

The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function.

HINT:
·

A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly. The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls its respective systems based on this pulse signal.

·

If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the following diagram will not operate normally.



WIRING DIAGRAM

E419027E25
1.542,0.271 2.688,0.531 1.146,0.26 10 false to Other Systems 2.115,1.417 2.427,1.615 0.313,0.198 10 false +S 2.427,1.292 2.74,1.49 0.313,0.198 10 false 6 4.583,1.323 4.896,1.521 0.313,0.198 10 false 17 4.833,1.427 5.281,1.646 0.448,0.219 10 false SPD 4.354,2.094 4.833,2.302 0.479,0.208 10 false M37 4.354,2.26 6.854,2.521 2.5,0.26 10 false Stereo Component Amplifier Assembly 1.01,2.073 1.781,2.271 0.771,0.198 10 false H21 1.01,2.24 2.979,2.594 1.969,0.354 10 false Combination Meter Assembly

PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
a.
E393685C46
1.49,0.344 1.917,0.615 0.427,0.271 2.438,1.938 2.177,1.333 false 0.188,0.188 0.5,0.385 0.313,0.198 10 false *a 1.573,0.406 2.031,0.604 0.458,0.198 10 false H21 2.385,1.958 2.698,2.156 0.313,0.198 10 false +S 2.771,3.594 3.229,3.792 0.458,0.198 10 false GND 1.125,3.844 1.281,4.042 0.156,0.198 10 false A
*a Component with harness connected
(Combination Meter Assembly)


Check the output waveform.

i.

Remove the combination meter assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal H21-6 (+S) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal H21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)

NG

2.INSPECT STEREO COMPONENT AMPLIFIER ASSEMBLY (INPUT WAVEFORM)
a.
E276235C19
1.604,0.333 1.958,0.594 0.354,0.26 2.656,2.083 2.823,1.333 false 0.083,0.083 0.333,0.25 0.25,0.167 10 false *a 1.656,0.385 1.99,0.552 0.333,0.167 10 false M37 2.5,2.104 2.833,2.271 0.333,0.167 10 false SPD 2.802,3.583 3.135,3.75 0.333,0.167 10 false GND 1.146,3.833 1.396,4 0.25,0.167 10 false A
*a Component with harness connected
(Stereo Component Amplifier Assembly)


Check the input waveform.

i.

Remove the stereo component amplifier assembly with the connector(s) still connected.


ii.

Connect an oscilloscope to terminal M37-17 (SPD) and body ground.


iii.

Turn the ignition switch to ON.


iv.

Turn a wheel slowly.


v.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal M37-17 (SPD) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Vehicle condition Wheel being rotated

OK:

The waveform is similar to that shown in the illustration.


HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.




Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR