Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086889 METER / GAUGE / DISPLAY _0416706 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speed Signal Circuit  


DESCRIPTION

HINT:

This circuit is used for the systems connected to terminal +S. This signal is not used for combination meter assembly operation. Combination meter assembly components such as the speedometer operate using data received via CAN communication. In addition, for some systems, vehicle speed information may be received via CAN communication.


FOR HV MODEL


The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the No. 2 skid control ECU (brake actuator assembly) which uses this information to create the vehicle speed signal. The vehicle speed signal consists of pulses sent to the combination meter assembly from the No. 2 skid control ECU (brake actuator assembly). To create this signal, 12 V is output from the combination meter assembly. This voltage is sent to the No. 2 skid control ECU (brake actuator assembly). The pulse signal is created by switching the transistor in the No. 2 skid control ECU (brake actuator assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the No. 2 skid control ECU (brake actuator assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.


FOR GASOLINE MODEL


The combination meter assembly receives the vehicle speed signal from this circuit. The wheel speed sensors produce an output that varies according to the vehicle speed. The wheel speed sensor output is received by the skid control ECU (brake actuator assembly) which uses this information to create the vehicle speed signal. The vehicle speed signal consists of pulses sent to the combination meter assembly from the skid control ECU (brake actuator assembly). To create this signal, 12 V is output from the combination meter assembly. This voltage is sent to the skid control ECU (brake actuator assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake actuator assembly) on and off, making the voltage on the wire drop to 0 V. A similar system is used for the output of this signal from the combination meter assembly via terminal +S. A voltage of 12 V is applied to terminal +S from each ECU or relay that is connected to this terminal. The transistor in the combination meter assembly is controlled by the signal from the skid control ECU (brake actuator assembly). When this transistor is turned on, this transistor makes the voltage supplied by the various ECUs (via their respective internal resistors) drop to 0 V. Each ECU connected to terminal +S of the combination meter assembly controls its respective system based on this pulse signal.


WIRING DIAGRAM

E456814E02
5.208,2.792 7.073,3.125 1.865,0.333 10 false Combination Meter Assembly 0.25,5.75 2.052,6.198 1.802,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.188,1.573 2.094,2.167 1.906,0.594 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 0.958,4.385 1.417,4.583 0.458,0.198 10 false ECM 5.208,8.771 6.948,9.156 1.74,0.385 10 false Stereo Component Amplifier Assembly 5.26,5.771 6.958,6.198 1.698,0.427 10 false Radio Receiver Assembly 0.635,7.417 1.708,7.708 1.073,0.292 10 false Navigation ECU 2.458,0.885 2.771,1.083 0.313,0.198 10 false *1 2.938,1.615 3.25,1.813 0.313,0.198 10 false *2 4.417,6.781 4.729,6.979 0.313,0.198 10 false *3 2.542,6.781 2.854,6.979 0.313,0.198 10 false *4 3.646,7.708 3.958,7.906 0.313,0.198 10 false *5 0.198,8.771 3.396,9.125 3.198,0.354 10 false *3: w/ Telematics System (for ERA-GLONASS) 0.198,8.448 2.938,8.74 2.74,0.292 10 false *2: for Gasoline Model 0.198,9.427 2.49,9.625 2.292,0.198 10 false *5: for 11 Speakers 5.573,1.969 5.885,2.167 0.313,0.198 10 false +S 1.302,0.885 1.76,1.083 0.458,0.198 10 false SP1 5.948,0.542 6.563,0.74 0.615,0.198 10 false 12 V 5.583,6.781 6.042,6.979 0.458,0.198 10 false SPDP 1.302,3.75 1.76,3.948 0.458,0.198 10 false SPD 1.302,5.26 1.76,5.458 0.458,0.198 10 false SPD 5.583,5.271 6.042,5.469 0.458,0.198 10 false SPD 1.302,6.781 1.76,6.979 0.458,0.198 10 false SPD 5.573,0.875 5.885,1.073 0.313,0.198 10 false SI 0.198,9.094 1.979,9.385 1.781,0.292 10 false *4: w/ Navigation System 5.583,8.302 6.042,8.5 0.458,0.198 10 false SPD 1.302,2.208 1.76,2.406 0.458,0.198 10 false SP1 0.292,2.906 1.865,3.5 1.573,0.594 10 false Skid Control ECU (Brake Actuator Assembly) 5.375,7.406 7.073,7.833 1.698,0.427 10 false Telematics Transceiver 0.198,8.125 2.49,8.323 2.292,0.198 10 false *1: for HV Model 0.198,1.406 0.656,1.604 0.458,0.198 10 false A57 1.708,0.885 2.021,1.083 0.313,0.198 10 false 18 0.302,2.74 0.76,2.938 0.458,0.198 10 false A39 1.708,2.208 2.021,2.406 0.313,0.198 10 false 18 5.354,0.875 5.667,1.073 0.313,0.198 10 false 5 2.542,3.75 2.854,3.948 0.313,0.198 10 false *2 5.354,1.969 5.667,2.167 0.313,0.198 10 false 6 0.979,4.219 1.438,4.417 0.458,0.198 10 false A28 1.708,3.75 2.021,3.948 0.313,0.198 10 false 39 5.208,2.635 5.667,2.833 0.458,0.198 10 false H21 1.708,5.26 2.021,5.458 0.313,0.198 10 false 19 5.292,5.271 5.604,5.469 0.313,0.198 10 false 27 0.26,5.583 0.719,5.781 0.458,0.198 10 false H48 5.25,4.063 5.708,4.26 0.458,0.198 10 false H1 1.719,6.781 2.031,6.979 0.313,0.198 10 false 9 5.281,6.781 5.594,6.979 0.313,0.198 10 false 10 5.365,7.25 5.823,7.448 0.458,0.198 10 false H10 0.635,7.25 1.094,7.448 0.458,0.198 10 false H18 5.281,8.302 5.594,8.5 0.313,0.198 10 false 11 5.208,8.615 5.667,8.813 0.458,0.198 10 false M38 2.177,9.104 4.344,9.427 2.167,0.323 10 false *6: for 8 Inch Multi-display Type 2.177,9.448 4.646,9.667 2.469,0.219 10 false *7: for 12.3 Inch Multi-display Type 4.406,5.26 4.719,5.458 0.313,0.198 10 false *7 5.25,4.229 6.948,4.656 1.698,0.427 10 false Radio and Display Receiver Assembly 5.573,3.75 6.031,3.948 0.458,0.198 10 false SPD 5.292,3.75 5.604,3.948 0.313,0.198 10 false 27 4.385,3.75 4.698,3.948 0.313,0.198 10 false *6 5.26,5.604 5.573,5.802 0.313,0.198 10 false H4

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)
E428098C03
1.521,0.396 1.896,0.646 0.375,0.25 2.281,1.229 2.396,0.625 true 0.167,0.49 0.479,0.688 0.313,0.198 10 false *a 1.573,0.438 1.906,0.646 0.333,0.208 10 false H21 2.396,0.458 2.594,0.667 0.198,0.208 10 false SI 2.76,3.656 3.208,3.979 0.448,0.323 10 false GND 1.073,3.927 1.385,4.135 0.313,0.208 10 false A 0.188,2.5 0.5,2.698 0.313,0.198 10 false *b
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection H21-5 (SI) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

HINT:

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.



Result:
Result Proceed to
The measured waveform is similar to that in the illustration A
The measured waveform is not similar to that in the illustration
(Stuck low)
B
The measured waveform is not similar to that in the illustration
(Stuck high)
C



A

2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)

B

6.CONFIRM MODEL

C

11.CONFIRM MODEL
2.INSPECT COMBINATION METER ASSEMBLY (OUTPUT WAVEFORM)
E436088C08
1.521,0.469 1.885,0.719 0.365,0.25 2.167,1.229 2.417,0.656 true 0.177,0.583 0.667,0.896 0.49,0.313 10 false *a 2.396,0.479 2.823,0.708 0.427,0.229 10 false +S 2.938,3.708 3.313,3.969 0.375,0.26 10 false GND 1.573,0.5 2.063,0.927 0.49,0.427 10 false H21 1.271,3.99 1.427,4.188 0.156,0.198 10 false A 0.167,2.49 0.479,2.688 0.313,0.198 10 false *b 0.802,3.396 0.958,3.594 0.156,0.198 10 false B
*a Component with harness connected
(Combination Meter Assembly)
*b Waveform


a.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester connection H21-6 (+S) - Body ground
Tool setting 5 V/DIV., 20 ms./DIV.
Condition Ignition switch ON, wheel being rotated

HINT:
·

When the system is functioning normally, one wheel revolution generates 4 pulses. As the vehicle speed increases, the width indicated by (A) in the illustration narrows.

·

The waveform (B) changes depending on the connected ECUs.




Result:
Result Proceed to
The measured waveform is similar to that in the illustration A
The measured waveform is not similar to that in the illustration
(Stuck low)
B
The measured waveform is not similar to that in the illustration
(Stuck high)
C



A

3.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)

B

4.INSPECT EACH ECU (INTERNAL SHORT)

C

REPLACE COMBINATION METER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the A28 ECM connector.*1


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the H1 radio and display receiver assembly connector.*5


d.

Disconnect the H4 radio receiver assembly connector.*6


e.

Disconnect the H10 telematics transceiver connector.*2


f.

Disconnect the H18 navigation ECU connector.*3


g.

Disconnect the M38 stereo component amplifier assembly connector.*4


h.

Disconnect the H21 combination meter assembly connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-39 (SPD) - H21-6 (+S)*1 Always Below 1 Ω
H48-19 (SPD) - H21-6 (+S) Always Below 1 Ω
H1-27 (SPD) - H21-6 (+S)*5 Always Below 1 Ω
H4-27 (SPD) - H21-6 (+S)*6 Always Below 1 Ω
H10-10 (SPDP) - H21-6 (+S)*2 Always Below 1 Ω
H18-9 (SPD) - H21-6 (+S)*3 Always Below 1 Ω
M38-11 (SPD) - H21-6 (+S)*4 Always Below 1 Ω


*1: for Gasoline Model

*2: w/ Telematics System (for ERA-GLONASS)

*3: w/ Navigation System

*4: for 11 Speakers

*5: for 8 Inch Multi-display Type

*6: for 12.3 Inch Multi-display Type



Result:
Proceed to
OK
NG



OK

CHECK THE VOLTAGE AT TERMINAL SPD OR SPDP OF EACH ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT EACH ECU (INTERNAL SHORT)
E436083C02
1.469,0.177 1.917,0.438 0.448,0.26 2.188,0.927 2.625,0.406 true 1.573,0.24 2.031,0.438 0.458,0.198 10 false H21 2.646,0.271 2.958,0.469 0.313,0.198 10 false +S 0.271,0.313 0.583,0.51 0.313,0.198 10 false *a
*a Component with harness connected
(Combination Meter Assembly)


a.

Disconnect one of the connectors below.

NOTICE:

After disconnecting a connector, perform all steps with all other ECUs connected.


Connector ECU
A28*1 ECM
H48 Certification ECU (smart key ECU assembly)
H1*5 Radio and display receiver assembly
H4*6 Radio receiver assembly
H10*2 Telematics transceiver
H18*3 Navigation ECU
M38*4 Stereo component amplifier assembly

*1: for Gasoline Model

*2: w/ Telematics System (for ERA-GLONASS)

*3: w/ Navigation System

*4: for 11 Speakers

*5: for 8 Inch Multi-display Type

*6: for 12.3 Inch Multi-display Type



b.

Measure the voltage according to the value(s) in the table below.

NOTICE:

Make sure to perform this inspection with the wheels stopped.


Standard Voltage:
Tester Connection Condition Specified Condition
H21-6 (+S) - Body ground Ignition switch ON 5 to 14 V



c.

Repeat steps (a) and (b) for each connected ECU.

HINT:

If the voltage changed to the specified voltage after disconnecting a connector, an internal short in the disconnected ECU is suspected.



Result:
Result Proceed to
After performing the inspection procedure for all connectors, the voltage did not change to the specified voltage A
When disconnecting the connector of the ECM, the voltage changed to the specified voltage
(for Gasoline Model)
B
When disconnecting the connector of the certification ECU (smart key ECU assembly), the voltage changed to the specified voltage C
When disconnecting the connector of the radio and display receiver assembly, the voltage changed to the specified voltage
(for 8 Inch Multi-display Type)
D
When disconnecting the connector of the radio receiver assembly, the voltage changed to the specified voltage
(for 12.3 Inch Multi-display Type)
E
When disconnecting the connector of the telematics transceiver, the voltage changed to the specified voltage
(w/ Telematics System (for ERA-GLONASS))
F
When disconnecting the connector of the navigation ECU, the voltage changed to the specified voltage
(w/ Navigation System)
G
When disconnecting the connector of the stereo component amplifier assembly, the voltage changed to the specified voltage
(for 11 Speakers)
H



A

5.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)

B

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

D

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

E

REPLACE RADIO RECEIVER ASSEMBLY

F

G

H

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (EACH ECU - COMBINATION METER ASSEMBLY)
a.

Disconnect the A28 ECM connector.*1


b.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the H1 radio and display receiver assembly connector.*5


d.

Disconnect the H4 radio receiver assembly connector.*6


e.

Disconnect the H10 telematics transceiver connector.*2


f.

Disconnect the H18 navigation ECU connector.*3


g.

Disconnect the M38 stereo component amplifier assembly connector.*4


h.

Disconnect the H21 combination meter assembly connector.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-39 (SPD)*1, H48-19 (SPD), H1-27 (SPD)*5, H4-27 (SPD)*6, H10-10 (SPDP)*2, H18-9 (SPD)*3 or M38-11 (SPD)*4 - H21-6 (+S) Always Below 1 Ω
A28-39 (SPD)*1, H48-19 (SPD), H1-27 (SPD)*5, H4-27 (SPD)*6, H10-10 (SPDP)*2, H18-9 (SPD)*3, M38-11 (SPD)*4 or H21-6 (+S) - Body ground Always 10 kΩ or higher


*1: for Gasoline Model

*2: w/ Telematics System (for ERA-GLONASS)

*3: w/ Navigation System

*4: for 11 Speakers

*5: for 8 Inch Multi-display Type

*6: for 12.3 Inch Multi-display Type



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

7.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)

B

9.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
7.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E430475C05
1.51,0.292 1.896,0.521 0.385,0.229 0.979,0.49 1.292,1.271 true 1.573,0.323 2.031,0.521 0.458,0.198 10 false A57 0.792,0.292 1.25,0.49 0.458,0.198 10 false SP1 0.094,0.063 0.552,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to No. 2 Skid Control ECU (Brake Actuator Assembly))


a.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A57-18 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

8.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-18 (SP1) or H21-5 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)
E430475C06
1.51,0.292 1.896,0.521 0.385,0.229 0.979,0.49 1.292,1.271 true 1.573,0.323 2.031,0.521 0.458,0.198 10 false A39 0.792,0.292 1.25,0.49 0.458,0.198 10 false SP1 0.094,0.063 0.552,0.26 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A39-18 (SP1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-18 (SP1) or H21-5 (SI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

12.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)

B

13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the A57 No. 2 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A57-18 (SP1) - H21-5 (SI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - COMBINATION METER ASSEMBLY)
a.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the H21 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-18 (SP1) - H21-5 (SI) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR