Home › Engine / Hybrid System › CRUISE CONTROL › LANE CONTROL SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _086858 CRUISE CONTROL _0418322 LANE CONTROL SYSTEM J

CRUISE CONTROL  LANE CONTROL SYSTEM  Indicator Circuit  


DESCRIPTION

The forward recognition camera sends indicator illumination request signals to the combination meter assembly via CAN communication.

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.READ VALUE USING GTS (CAN BUS CHECK)
a.

Using the GTS, perform CAN bus diagnostics and check that there are no malfunctions in ECUs connected to the CAN communication system.

CAN Bus Check
50007

Result:
Result Proceed to
All of the ECUs and sensors that are currently connected to the CAN communication system are displayed A
None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed B



A

2.CHECK FOR DTCs (HEALTH CHECK)

B

2.CHECK FOR DTCs (HEALTH CHECK)
a.

Check for DTCs.


b.

Turn the ignition switch off.


Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

3.PERFORM ACTIVE TEST USING GTS

B

GO TO DTC CHART

3.PERFORM ACTIVE TEST USING GTS
a.

According to the display on the GTS, perform the Active Test.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Multi Display All (White) Multi-information display (White display) OFF or ON -
Body Electrical > Combination Meter > Active Test
Tester Display
Multi Display All (White)
50004 409 20

b.

Turn the ignition switch off.


Result:
Result Proceed to
The multi-information display turns on according to the operation of the Active Test A
The multi-information display does not turn on according to the operation of the Active Test B



A

4.READ VALUE USING GTS

B

REPLACE COMBINATION METER ASSEMBLY

4.READ VALUE USING GTS
a.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Lane control system control status Prohibit or Permit Prohibit: Control prohibited
Permit: Control permitted
-
Chassis > Lane Control > Data List
Tester Display
LDA Control
50003 418 3

Result:
Result Proceed to
The LTA indicator illuminates and the Data List item LDA Control changes according to the operation of the LTA main switch A
The LTA indicator does not illuminate but the Data List item LDA Control changes according to the operation of the LTA main switch B
The LTA indicator does not illuminate and the Data List item LDA Control does not change according to the operation of the LTA main switch C



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE COMBINATION METER ASSEMBLY

C

REPLACE FORWARD RECOGNITION CAMERA