The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.
If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U010487 | Lost Communication with Cruise Control Module Missing Message | Detection condition:
Ignition switch ON Malfunction status:
Communication malfunction with the forward recognition camera is detected Malfunction duration:
10 seconds or more |
·
CAN bus line ·
Forward recognition camera ·
Millimeter wave radar sensor assembly |
| Pattern | DTC output part name
(Display on GTS) |
Suspected Area (Malfunction Status) | |
|---|---|---|---|
| Millimeter Wave Radar Sensor Assembly
(Front Radar Sensor) |
Forward Recognition Camera
(Pre-Collision System) |
||
| U010487 | U023587 | ||
|
○: DTC is output -: DTC is not output |
|||
| Pattern 1 | ○ | ○ | ·
Open in CAN communication line (forward recognition camera - millimeter wave radar sensor assembly) ·
Short in CAN communication line ·
Open or short in forward recognition camera internal circuit ·
Open or short in millimeter wave radar sensor assembly internal circuit |
| Pattern 2 | ○ | - | ·
Forward recognition camera connector disconnected ·
Forward recognition camera power supply circuit malfunction ·
Forward recognition camera internal malfunction ·
Millimeter wave radar sensor assembly internal malfunction |
If the DTCs are output simultaneously, the inspection area can be narrowed down.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.
When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.
Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.
When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.
Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.
One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)
Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT
Check for pre-collision system DTCs.
| Result | Proceed to |
|---|---|
| DTC U023587 is output | A |
| DTC U023587 is not output | B |
A
B
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
- | - |
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R5-6 (CANH) - R5-12 (CANL) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132Ω |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R5-6 (CANH) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-12 (CANL) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| R5-6 (CANH) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| R5-12 (CANL) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
Connect the R5 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | DLC3 | - | - |
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
- | - |
Disconnect the B6 millimeter wave radar sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B6-5 (CA1P) - B6-6 (CA1N) | Cable disconnected from negative (-) auxiliary battery terminal | 108 to 132Ω |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B6-5 (CA1P) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B6-6 (CA1N) - H56-4 (CG) | Cable disconnected from negative (-) auxiliary battery terminal | 200 Ω or higher |
| B6-5 (CA1P) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
| B6-6 (CA1N) - H56-16 (BAT) | Cable disconnected from negative (-) auxiliary battery terminal | 6 kΩ or higher |
Connect the B6 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the locking part and terminals of the forward recognition camera connector.
Make sure the connector is not loose or disconnected.
Make sure that the connector and terminals are not deformed or corroded.
The connector and terminals are normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Forward Recognition Camera) |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the R5 forward recognition camera connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R5-10 (GND) - Body ground | Always | Below 1 Ω |
Connect the cable to the negative (-) auxiliary battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R5-7 (IGB) - Body ground | Ignition switch ON | 11 to 14 V |
Connect the R5 forward recognition camera connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly) |
*b | Waveform |
Turn the ignition switch off.
Disconnect the B6 millimeter wave radar sensor assembly connector.
Turn the ignition switch to ON.
Using an oscilloscope, measure the waveform at the B6 millimeter wave radar sensor assembly connector.
| Tester Connection | Condition | Tool Setting |
|---|---|---|
| B6-5 (CA1P) - Body ground | Ignition switch ON | 1 V/DIV., 100 μs/DIV. |
The oscilloscope waveform is for reference only and does not include noise, fluctuations, etc.
A waveform similar to that in the illustration can be observed.
Connect the B6 millimeter wave radar sensor assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG