1. PREPARATION FOR MILLIMETER WAVE RADAR SENSOR ASSEMBLY ADJUSTMENT
| *a | 2.5 m (8.2 ft.) |
| *b | 2 m (6.6 ft.) |
|
Do not place any metal objects in this area |
|
Do not place metal objects with a height of more than 50 mm (1.97 in.) in this area |
Park the vehicle on a level surface where the area in front of the vehicle shown in the illustration is free of metal objects.
Metal objects with a height of 50 mm (1.97 in.) or less placed within the area shown in the illustration will not affect the adjustment.
Check the levelness of the ground.
| *a | 1.5 m (4.92 ft.) |
|
Levelness Check Point |
Check the levelness of the ground at the 3 points shown in the illustration.
Place the level on each levelness check point and check that the air bubble of the level is centered.
Adjust the tire inflation pressure to the specified pressure.
Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION
Clean the front emblem or millimeter wave radar sensor assembly.
Visually inspect the front of the vehicle.
Confirm that there is no damage or deformation.
Visually inspect the front bumper assembly, radiator grille and stays.
Confirm that there is no damage or deformation.
2. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY VERTICALLY AND HORIZONTALLY
| *a | SST (Flat Surface Target) |
| *b | SST (Panel Stand) |
Adjust SST (flat surface target) height.
Check that SST (flat surface target) has no damage or deformation.
Check that SST (flat surface target) is assembled correctly.
Check that SST (flat surface target) has no looseness or wobble.
| *a | Handle |
| *b | Scale |
| *c | Height Reference Line |
Loosen the top and bottom handles of SST (panel stand), and while checking the included scale, adjust the height of SST (flat surface target) as shown in the illustration so that its height reference line is at the same height as the millimeter wave radar sensor assembly, then re-tighten the top and bottom handles.
Adjust SST (flat surface target) so that its center is aligned with the millimeter wave radar sensor assembly (center of emblem).
Height adjustment can be performed using the scale included with SST (flat surface target).
896 mm (2.94 ft.)
Place SST (flat surface target).
Hang a weight with a pointed tip from the center of the rear emblem, and mark the rear center point of the vehicle (point A) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Hang a weight with a pointed tip from the center of the front emblem, and mark the front center point of the vehicle (point B) on the ground.
| *a | String | *b | Weight |
| *c | Center | - | - |
Lightly flick the string with your fingers several times to confirm that the string is perpendicular to the ground.
Using tape and a string, create a line that connects point B to point A and extends at least 1500 mm (4.92 ft.) beyond the front center point of the vehicle.
| *a | String | *b | Tape |
| *c | 1500 mm (4.92 ft.) | - | - |
Make sure the string is taut when securing it with tape.
Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.
Mark point C (SST (flat surface target) placement position) at a position 1500 mm (4.92 ft.) from point B.
Position SST (panel stand) so that it is aligned with the target position line and the mark-off line is aligned with point C as shown in the illustration.
| *a | SST (Panel Stand) | *b | Mark-off Line |
| *c | Reference Line | - | - |
Make sure that the mark-off lines of the SST (panel stand) are aligned with the reference line.
Front Beam Axis Adjustment:
Close all of the doors.
Ensure that nobody enters the adjustment area during the adjustment.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Do not turn off the GTS or ignition switch.
If the vehicle moves or is shaken during beam axis adjustment such as during strong winds or a door is opened or closed, perform the adjustment again.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Adjustment.
| Tester Display |
|---|
| Front Beam Axis Adjustment |
Confirm the conditions displayed on the screen and then press "Next".
Select "Flat surface" and then press "Next".
Perform the adjustment according to the display on the GTS.
If an error code is displayed, perform troubleshooting according to the following table, then perform the adjustment again.
Press "Exit" to finish front beam axis adjustment.
Front Beam Axis Misalignment Reading:
Close all of the doors.
Do not move or shake the vehicle during adjustment (do not get in or out of the vehicle).
Ensure that nobody enters the adjustment area during the adjustment.
Do not turn off the GTS or ignition switch.
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Beam Axis Misalignment Reading.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
Confirm the conditions displayed on the screen and then press "Next".
Select "Flat surface" and then press "Next".
Perform the adjustment according to the display on the GTS.
| Vertical | -0.5 to 0.5 deg. |
| Horizontal | -0.5 to 0.5 deg. |
If the result is not as specified, perform beam axis adjustment again.
Front Radar Acceleration Sensor Calibration:
Enter the following menus: Body Electrical / Front Radar Sensor / Utility / Front Radar Acceleration Sensor Calibration.
| Tester Display |
|---|
| Front Radar Acceleration Sensor Calibration |
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
After beam axis adjustment completes, clear the following system vehicle control history entries.
Clear vehicle control history (Dynamic Radar Cruise Control System).
for HV Model: Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM (for HV Model)>VEHICLE CONTROL HISTORY
for Gasoline Model: Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model)>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lane Control System).
Click hereEngine / Hybrid System>CRUISE CONTROL>LANE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Road Sign Assist System).
Click hereEngine / Hybrid System>CRUISE CONTROL>ROAD SIGN ASSIST SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Front Radar Sensor System).
Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT RADAR SENSOR SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Pre-collision System).
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>VEHICLE CONTROL HISTORY
Clear vehicle control history (Lighting System).
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>VEHICLE CONTROL HISTORY