Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086893 PRE-COLLISION _0418188 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message  


DESCRIPTION

The forward recognition camera and millimeter wave radar sensor assembly communicate via CAN communication. If a signal is not received from the millimeter wave radar sensor assembly, the forward recognition camera stores a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Single Sensor or Center Missing Message 3 seconds or more after the ignition switch is turned to ON, a communication malfunction with the millimeter wave radar sensor assembly is detected for 2 seconds or more.
·

CAN bus line

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



Pattern DTC Location Name
(GTS Displayed Name)
Suspected Area (Malfunction Status)
Forward recognition camera
(Pre-Collision System)
Millimeter wave radar sensor assembly
(Front Radar Sensor)
U023587 U010487

○: DTC is stored

-: DTC is not stored

Pattern 1 ○ ○
·

Open in CAN communication line (forward recognition camera - millimeter wave radar sensor assembly)

·

Short in CAN communication line

·

Open or short in forward recognition camera internal circuit

·

Open or short in millimeter wave radar sensor assembly internal circuit

·

Harness or connector


Pattern 2 ○ -
·

Millimeter wave radar sensor assembly connector disconnected

·

Millimeter wave radar sensor assembly power supply circuit malfunction

·

Millimeter wave radar sensor assembly internal malfunction

·

Forward recognition camera internal malfunction

·

Harness or connector



HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


WIRING DIAGRAM

B330403E06
0.75,1.74 2.729,1.938 1.979,0.198 10 false Forward Recognition Camera 4.365,1.75 7.094,1.99 2.729,0.24 10 false Millimeter Wave Radar Sensor Assembly 0.75,1.573 1.063,1.771 0.313,0.198 10 false R5 4.365,1.563 4.677,1.76 0.313,0.198 10 false B6 1.604,0.792 2.219,0.99 0.615,0.198 10 false CANH 1.615,1.469 2.229,1.667 0.615,0.198 10 false CANL 5.115,0.771 5.729,0.969 0.615,0.198 10 false CA1P 5.125,1.479 5.74,1.677 0.615,0.198 10 false CA1N 2.083,0.781 2.24,0.979 0.156,0.198 10 false 6 2.073,1.25 2.271,1.448 0.198,0.198 10 false 12 4.948,0.771 5.104,0.969 0.156,0.198 10 false 5 4.948,1.24 5.104,1.438 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly beam axis alignment and to clear the vehicle control history. Before performing the Driving Adjustment, make sure to read Before Starting Driving Adjustment.

HINT:

Beam axis alignment of the millimeter wave radar sensor assembly can be performed using either Triangle Target, Flat Surface Target or Driving Adjustment.

Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)

Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT


·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.CHECK FOR DTCs
a.

Using the GTS, check for front radar sensor system DTCs.

Body Electrical > Front Radar Sensor > Trouble Codes
50001 429

Result:
Result Proceed to
DTC U010487 is output A
DTC U010487 is not output B



A

2.CHECK CAN BUS LINES

B

4.CHECK CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
2.CHECK CAN BUS LINES
B515747C40
1.771,0.427 2.115,0.646 0.344,0.219 4.917,0.375 5.26,0.594 0.344,0.219 2.333,1.417 2.583,0.667 2.583,0.667 2.833,0.667 true 2.333,1.75 2.583,2.333 2.583,2.333 2.833,2.333 true 5,1.135 4.75,0.469 4.75,0.469 4.5,0.469 true 5.75,1.708 5.583,2.292 5.583,2.292 5.333,2.292 true 4.01,0.219 4.323,0.375 0.313,0.156 10 false *1 1.25,0.219 1.563,0.375 0.313,0.156 10 false *a 1.865,0.458 2.177,0.656 0.313,0.198 10 false R5 4.969,0.406 5.281,0.604 0.313,0.198 10 false H56 2.885,0.573 3.5,0.771 0.615,0.198 10 false CANH 2.885,2.24 3.5,2.438 0.615,0.198 10 false CANL 4.26,0.396 4.875,0.594 0.615,0.198 10 false CG 5.031,2.208 5.646,2.406 0.615,0.198 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Forward Recognition Camera)
- -


a.

Disconnect the R5 forward recognition camera connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-6 (CANH) - R5-12 (CANL) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-6 (CANH) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-12 (CANL) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
R5-6 (CANH) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
R5-12 (CANL) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.

Connect the R5 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

3.CHECK CAN BUS LINES
3.CHECK CAN BUS LINES
B515746C38
1.854,0.396 2.208,0.625 0.354,0.229 4.99,0.365 5.344,0.594 0.354,0.229 1.417,2.25 1.667,2.25 1.667,2.25 1.833,1.583 true 1.948,1.583 2.115,2.25 2.115,2.25 2.365,2.25 true 4.583,0.583 4.833,0.583 4.833,0.583 5.104,1.125 true 5.823,1.719 5.667,2.25 5.667,2.25 5.417,2.25 true 4.167,0.271 4.479,0.427 0.313,0.156 10 false *1 1.292,0.292 1.604,0.448 0.313,0.156 10 false *a 1.958,0.448 2.177,0.646 0.219,0.198 10 false B6 5.052,0.406 5.51,0.604 0.458,0.198 10 false H56 1.042,2.198 1.656,2.396 0.615,0.198 10 false CA1P 2.427,2.188 3.042,2.385 0.615,0.198 10 false CA1N 4.354,0.521 4.667,0.719 0.313,0.198 10 false CG 5.115,2.188 5.552,2.406 0.438,0.219 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)
- -


a.

Disconnect the B6 millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B6-5 (CA1P) - B6-6 (CA1N) Cable disconnected from negative (-) auxiliary battery terminal 108 to 132 Ω



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B6-5 (CA1P) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B6-6 (CA1N) - H56-4 (CG) Cable disconnected from negative (-) auxiliary battery terminal 200 Ω or higher
B6-5 (CA1P) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher
B6-6 (CA1N) - H56-16 (BAT) Cable disconnected from negative (-) auxiliary battery terminal 6 kΩ or higher



d.

Connect the B6 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Check the locking part and terminals of the millimeter wave radar sensor assembly connector.

NOTICE:
·

Make sure the connector is not loose or disconnected.

·

Make sure that the connector and terminals are not deformed or damaged.



OK:

The connector and terminals are normal.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
A417826C39
1.49,0.146 1.875,0.375 0.385,0.229 0.792,0.75 1.396,1.052 true 1.958,1.229 2.563,1.531 true 0.125,0.125 0.438,0.281 0.313,0.156 10 false *a 1.594,0.188 1.906,0.385 0.313,0.198 10 false B6 0.354,0.667 0.969,0.865 0.615,0.198 10 false SGND 2.615,1.479 3.01,1.677 0.396,0.198 10 false IGB
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


a.

Disconnect the cable from the negative (-) auxiliary battery terminal.


b.

Disconnect the B6 millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B6-1 (SGND) - Body ground Always Below 1 Ω



d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B6-8 (IGB) - Body ground Ignition switch ON 11 to 14 V



f.

Connect the B6 millimeter wave radar sensor assembly connector.


Result:
Proceed to
OK
NG



OK

6.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (WAVEFORM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE CIRCUIT)

6.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY (WAVEFORM)
B330405C03
1.781,0.375 2.125,0.635 0.344,0.26 2.344,1.323 2.625,0.823 2.625,0.823 2.896,0.823 true 0.646,0.406 0.958,0.604 0.313,0.198 10 false *a 4.188,0.417 4.5,0.615 0.313,0.198 10 false *b 1.885,0.427 2.281,0.677 0.396,0.25 10 false R5 6.417,1.635 6.813,1.885 0.396,0.25 10 false GND 2.938,0.74 3.594,0.938 0.656,0.198 10 false CANH
*a Front view of wire harness connector
(to Forward Recognition Camera)
*b Waveform


a.

Turn the ignition switch off.


b.

Disconnect the R5 forward recognition camera connector.


c.

Turn the ignition switch to ON.


d.

Using an oscilloscope, measure the waveform at the R5 forward recognition camera connector.

Measurement Condition:
Tester Connection Condition Tool Setting
R5-6 (CANH) - Body ground Ignition switch ON 1 V/DIV., 100 μs/DIV.


NOTICE:

The oscilloscope waveform is for reference only and does not include noise, fluctuations, etc.


OK:

A waveform similar to that in the illustration can be observed.



e.

Connect the R5 forward recognition camera connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY