After the combination meter assembly has started, the combination meter assembly attempts to detect the radio and display receiver assembly*1 or radio receiver assembly*2 by performing communication via local bus.
This DTC is stored when the radio and display receiver assembly*1 or radio receiver assembly*2 has been detected but communication between the combination meter assembly and radio and display receiver assembly*1 or radio receiver assembly*2 is interrupted.
*1: for 8 Inch Multi-display Type
*2: for 12.3 Inch Multi-display Type
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B132187 | Lost Communication with EMV Missing Message | Diagnosis Condition (for 8 Inch Multi-display Type):
·
The combination meter assembly has started ·
The radio and display receiver assembly has started Diagnosis Condition (for 12.3 Inch Multi-display Type): ·
The combination meter assembly has started ·
The radio receiver assembly has started Malfunction Status (for 8 Inch Multi-display Type): After the radio and display receiver assembly is detected, communication via local bus is interrupted Malfunction Status (for 12.3 Inch Multi-display Type): After the radio receiver assembly is detected, communication via local bus is interrupted Malfunction Time: 30 seconds or more |
·
Radio and display receiver assembly ·
Radio receiver assembly ·
Harness or connector ·
Combination meter assembly |
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/o Navigation System | A |
| w/ Navigation System | B |
A
B
Check if audio and visual system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Check if headup display system DTCs are output.
If DTC B132187 is output from the meter / gauge system and is not output from the headup display system, it can be suspected that the combination meter assembly has an internal malfunction.
If DTC B132187 is output from the headup display system and is not output from the audio and visual system, it can be suspected that the radio and display receiver assembly has an internal malfunction.
| Result | Proceed to |
|---|---|
| DTC B132187 is not output | A |
| DTC B132187 is output | B |
A
B
Check if navigation system DTCs are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
for 8 Inch Multi-display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>DIAGNOSTIC TROUBLE CODE CHART
for 12.3 Inch Multi-display Type: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>DIAGNOSTIC TROUBLE CODE CHART
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| w/ Headup Display System | A |
| w/o Headup Display System | B |
A
B
Check if headup display system DTCs are output.
If DTC B132187 is output from the meter / gauge system and is not output from the headup display system, it can be suspected that the combination meter assembly has an internal malfunction.
If DTC B132187 is output from the headup display system and is not output from the navigation system, it can be suspected that the radio and display receiver assembly*1 or radio receiver assembly*2 has an internal malfunction.
*1: for 8 Inch Multi-display Type
*2: for 12.3 Inch Multi-display Type
| Result | Proceed to |
|---|---|
| DTC B132187 is not output | A |
| DTC B132187 is output
(for 8 Inch Multi-display Type) |
B |
| DTC B132187 is output
(for 12.3 Inch Multi-display Type) |
C |
A
B
C
Replace the combination meter assembly with a new one.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Turn the ignition switch to ON.
Wait 30 seconds or more.
Check if meter / gauge system DTCs are output.
| Result | Proceed to |
|---|---|
| DTC B132187 is not output | A |
| DTC B132187 is output
(for 8 Inch Multi-display Type) |
B |
| DTC B132187 is output
(for 12.3 Inch Multi-display Type) |
C |
A
B
C