Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.11
RM37A0E _58 Vehicle Interior _086889 METER / GAUGE / DISPLAY _0416706 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the combination meter assembly. This circuit provides two types of power source; one is a constant power source, and the other is an IG power source.

WIRING DIAGRAM

E430486E04
5.323,1.26 5.635,1.458 0.313,0.198 10 false 39 5.323,0.656 5.635,0.854 0.313,0.198 10 false 40 5.385,1.854 5.542,2.052 0.156,0.198 10 false 2 5.323,2.375 5.635,2.563 0.313,0.188 10 false 21 5.594,1.365 6.052,1.563 0.458,0.198 10 false IG+ 5.594,0.781 5.75,0.979 0.156,0.198 10 false B 5.594,1.979 5.906,2.177 0.313,0.198 10 false EP 5.583,2.5 5.896,2.698 0.313,0.198 10 false ES 0.802,1.958 2.135,2.479 1.333,0.521 10 false from Engine Stop and Start ECU 3.01,0.927 5,1.125 1.99,0.198 10 false ECU-DCC NO. 2 3.104,1.521 4.479,1.719 1.375,0.198 10 false METER-IG2 0.802,1.344 3.865,1.542 3.063,0.198 10 false from IG2-NO. 2 Relay 0.792,0.781 4.156,0.979 3.365,0.198 10 false from Auxiliary Battery 5.094,3.083 5.552,3.281 0.458,0.198 10 false H21 5.094,3.25 7.073,3.5 1.979,0.25 10 false Combination Meter Assembly 4.052,1.833 4.365,2.031 0.313,0.198 10 false *1 4.052,1.25 4.365,1.448 0.313,0.198 10 false *2 0.365,3.292 4.646,3.49 4.281,0.198 10 false *1: w/ Stop and Start System 2.604,3.292 6.885,3.49 4.281,0.198 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.

·

Inspect the fuses of circuits related to this system before performing the following procedure.



PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE CIRCUIT)

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (IG POWER SOURCE CIRCUIT)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-39 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY POWER SOURCE CIRCUIT)

NG

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY POWER SOURCE CIRCUIT)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-40 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the H21 combination meter assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H21-39 (IG+) - Body ground Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
H21-40 (B) - Body ground Ignition switch off*1 11 to 14 V
Always*2 11 to 14 V


*1: for HV Model

*2: for Gasoline Model



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H21-2 (EP) - Body ground Always Below 1 Ω
H21-21 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR