Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _094408 STOP AND START _0444545 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Backup Boost Converter Circuit  


DESCRIPTION

A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control.

This prevents various functions such as the navigation system or audio and visual system from malfunctioning if the power source voltage drops due to the battery voltage dropping when the engine is restarted by stop and start control.

If any DTCs are output, troubleshoot the DTCs first.

HINT:

A relay function and fuse function are provided in the backup boost converter.

If there is a malfunction in any of the electrical system circuits connected to the backup boost converter, the fuse and relay functions shut off the malfunctioning circuit to protect other circuits (remains shut off until next trip).

When the electrical system circuit is shut off, power to the circuit is cut off, causing any systems connected to the circuit to be disabled.

The fuse function is reset* when the ignition switch is turned off. If the malfunction still exists in the electrical system circuit that has been shut off by the relay function, it will be shut off again by the relay and fuse functions the next time the ignition switch is turned to ON.

*: A semiconductor fuse self resets according to electric signal.

The backup boost converter supplies power to:
·

Electronically controlled brake system

·

Power steering system

·

Meter / gauge system

·

Audio and visual system

·

Navigation system

·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Tire pressure warning system

·

Lighting system (INT)

·

Air conditioning system

·

CAN communication system

·

Toyota safety sense

·

Parking support alert system

·

Headup display system

·

Blind spot monitor system

·

Fog light assembly


The external backup boost converter (eco run vehicle converter assembly) supplies power to:
·

Navigation system



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU assembly, perform learning of the external backup boost converter (eco run vehicle converter assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PROBLEM SYMPTOMS
a.

Determine the trouble area by referring to the table below.

Effect on Vehicle Trouble Area/Cause Fail-safe DTC Output Stop and start cancel indicator Symptom Proceed to
When the engine is restarted by stop and start control:
The following symptoms may occur
·

Navigation system is reset

·

Audio and visual system is reset

·

The combination meter assembly fades out

·

The steering wheel feels heavy when the engine is restarted*


Backup boost converter internal malfunction
·

Internal power source malfunction

·

Internal power source overvoltage

·

CPU duty malfunction

·

Communication cycle error


Stop and start control prohibited P323A00
P323AA2
P323B29
P323B38
Blinks Systems stop operating during engine restart as the backup boost converter output voltage cannot be boosted A
Battery voltage drop
Systems on the converter output side do not operate
B41 terminal: All of the following will not operate
·

Navigation system

·

Rear seat entertainment system

·

Fog light assembly

·

Headup display system


B42 terminal: Both of the following will not operate
·

Audio and visual system

·

Navigation system


B43 terminal: All of the following will not operate
·

Navigation system

·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Lighting system (INT)


IG41 terminal: All of the following will not operate
·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Air conditioning system

·

CAN communication system

·

Toyota safety sense

·

Parking support alert system

·

Headup display system

·

Blind spot monitor system


EMOP terminal: The oil pump with solenoid assembly will not operate
Overcurrent applied to an output terminal (output terminal relay circuit is shutoff) Stop and start control is prohibited
(Connected ECUs or sensors may detect power source malfunction DTCs)
P323A19 Blinks Systems do not operate as power supply from the converter is cut off A
Systems do not operate
(Due to converter input side malfunction)
IG1 terminal: Both of the following will not operate
·

Meter / gauge system

·

Rear seat entertainment system


IG2 terminal: All of the following will not operate
·

Electronically controlled brake system

·

Power steering system

·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Air conditioning system

·

CAN communication system

·

Toyota safety sense

·

Parking support alert system

·

Headup display system

·

Blind spot monitor system


ACC terminal: All of the following will not operate
·

Audio and visual system

·

Navigation system

·

Rear seat entertainment system


ILL terminal: Both of the following will not operate
·

Rear seat entertainment system

·

Air conditioning system


Converter input circuit malfunction
·

Open or short to GND in IG1 circuit

·

Open or short to GND in IG2 circuit

·

Open or short to GND in ACC circuit

·

Open or short to GND in ILL circuit


Stop and start control prohibited - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
Systems on the converter output side do not operate
(varies depending on the malfunctioning relay circuit the converter detected)
AC41 terminal: All of the following will not operate
·

Audio and visual system

·

Navigation system

·

Rear seat entertainment system


IG11 terminal:

The power steering system will not operate


IG12 terminal:

The meter / gauge system will not operate


IG31 terminal:

The Electronically controlled brake system will not operate


IG41 terminal: All of the following will not operate
·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Air conditioning system

·

CAN communication system

·

Toyota safety sense

·

Parking support alert system

·

Headup display system

·

Blind spot monitor system


B41 terminal: All of the following will not operate
·

Navigation system

·

Rear seat entertainment system

·

Fog light assembly

·

Headup display system


IL41 terminal: Both of the following will not operate
·

Rear seat entertainment system

·

Air conditioning system


B42 terminal: Both of the following will not operate
·

Audio and visual system

·

Navigation system


B43 terminal: All of the following will not operate
·

Navigation system

·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Lighting system (INT)


IL41 terminal: Both of the following will not operate
·

Rear seat entertainment system

·

Air conditioning system


Malfunction in circuits the converter supplies power to
(between the converter and ECUs or sensors)
Related systems do not operate as the relay circuit in the converter is turned off - Does not blink (Blinks when communication error DTCs are stored) Systems do not operate as power supply from the converter is cut off B
All of the following systems do not operate
·

Electronically controlled brake system

·

Power steering system

·

Meter / gauge system

·

Audio and visual system

·

Navigation system

·

Rear seat entertainment system

·

Digital rear-view mirror system

·

Auto glare-resistant EC mirror

·

Lighting system (INT)

·

Air conditioning system

·

CAN communication system

·

Toyota safety sense

·

Parking support alert system

·

Headup display system

·

Blind spot monitor system

·

Fog light assembly


·

Open in BBC fuse circuit

·

Short in converter circuit

·

Backup boost converter malfunction


Stop and start control prohibited P061519 Does not blink (Due to disabled meter / gauge system) All systems that the converter supplies power to do not operate (see circuit diagram) A
P30DF62
P30EF48
P323A00
P323A16
P323AA2
P323B29
P323B38
The audio does not operate
(until the ignition switch is turned off)
Excessive audio volume
Data List item "State of BBC" or "State of External BBC" displays "BBC Overcurrent" while the circuit is protected
The relay circuit in the converter is turned off to cut off power supply to the navigation system or audio and visual system (Returns to normal when the ignition switch is turned off) - Does not blink If overcurrent is detected in the navigation system or audio and visual system, system operation is disabled while the ignition switch is ON
(Returns to normal when the ignition switch is turned off)
C
·

The combination meter assembly cannot be turned off (short between IG12 and +B)

·

Communication error DTCs may be stored due to short between AC41 and +B


HINT:

Varies depending on the number of times an open occurs in the +B circuit


Converter circuit malfunction
·

Short between IG12 and +B

·

Short between AC41 and +B


- - Does not blink The converter cannot shut off the power source when the ignition switch is turned off B
·

Ignition switch cannot be turned off from ACC (short between ACC and +B)

·

Ignition switch cannot be turned off from ON (short between IG1 or IG2 and +B)


Engine stop and start ECU power source circuit malfunction
·

Short between ACC and +B

·

Short between IG1 and +B

·

Short between IG2 and +B


- - Does not blink Ignition switch cannot be turned off B
The navigation system cannot be turned off (short between ACC and BIN) External backup boost converter (eco run vehicle converter assembly) circuit malfunction
·

Short between ACC and BIN


- - Does not blink The external backup boost converter (eco run vehicle converter assembly) cannot shut off the power source when the ignition switch is turned off D

*: A DTC may be stored in the power steering system



Result:
Proceed to
A
B
C
D



A

B

2.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)

C

7.CHECK AUDIO SYSTEM

D

10.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
2.CHECK HARNESS AND CONNECTOR (BIN1 AND BIN2 TERMINALS POWER SOURCE CIRCUIT)
A346333C99
1.469,0.229 1.979,0.49 0.51,0.26 1.042,1.5 0.75,1.875 true 1.458,1.896 1.167,1.156 true 1.594,0.292 2.052,0.49 0.458,0.198 10 false A33 0.146,0.146 0.458,0.344 0.313,0.198 10 false *a 0.573,1.927 1,2.146 0.427,0.219 10 false BIN1 1.333,1.938 1.76,2.156 0.427,0.219 10 false BIN2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-1 (BIN2) - Body ground Always 9.5 to 14 V
A33-3 (BIN1) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1, IG2 AND ACC TERMINALS POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - BATTERY)

3.CHECK HARNESS AND CONNECTOR (IG1, IG2 AND ACC TERMINALS POWER SOURCE CIRCUIT)
A444508C17
1.49,0.344 2,0.625 0.51,0.281 2.021,1.49 2.052,1.854 true 1.604,1.49 1.396,1.844 true 1.469,1.5 0.979,1.875 true 1.615,0.406 2.063,0.583 0.448,0.177 10 false H66 0.094,0.104 0.406,0.302 0.313,0.198 10 false *a 1.948,1.896 2.333,2.115 0.385,0.219 10 false IG1 1.24,1.896 1.625,2.115 0.385,0.219 10 false ACC 0.844,1.906 1.229,2.125 0.385,0.219 10 false IG2
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Turn the ignition switch to ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H66-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Turn the ignition switch to ON.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H66-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V
H66-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V



f.

Turn the ignition switch to off.


g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H66-19 (ACC) - Body ground Ignition switch off 0 to 1 V
H66-21 (IG1) - Body ground Ignition switch off 0 to 1 V
H66-18 (IG2) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (+B TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (IG1-NO. 1, IG2-NO. 2 OR ACC RELAY))

4.CHECK HARNESS AND CONNECTOR (+B TERMINAL POWER SOURCE CIRCUIT)
A346332C51
1.615,0.417 2.042,0.688 0.427,0.271 0.781,1.208 0.688,1.719 true 1.708,0.469 2.167,0.667 0.458,0.198 10 false A34 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a 0.563,1.76 0.875,1.958 0.313,0.198 10 false +B
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


a.

Disconnect the engine stop and start ECU connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V



d.

Turn the ignition switch to off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-1 (+B) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE STOP AND START ECU - EFI-MAIN NO. 1 RELAY)

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - EACH ECU OR SENSOR)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Skid Control ECU (Brake Actuator Assembly)
Tester Connection Condition Specified Condition
H66-1 (IG31) - A39-45 (IG1) Always Below 1 Ω
H66-1 (IG31) or A39-45 (IG1) - Body ground and other terminals Always 10 kΩ or higher

Steering Sensor
Tester Connection Condition Specified Condition
H66-1 (IG31) - H57-9 (IG1) Always Below 1 Ω
H66-1 (IG31) or H57-9 (IG1) - Body ground and other terminals Always 10 kΩ or higher

Combination Meter Assembly
Tester Connection Condition Specified Condition
H66-10 (IG12) - H21-39 (IG+) Always Below 1 Ω
H66-10 (IG12) or H21-39 (IG+) - Body ground and other terminals Always 10 kΩ or higher

Power Steering ECU (Rack and Pinion Power Steering Gear Assembly)
Tester Connection Condition Specified Condition
H66-6 (IG11) - C67-4 (IG) Always Below 1 Ω
H66-6 (IG11) or C67-4 (IG) - Body ground and other terminals Always 10 kΩ or higher

Radio and Display Receiver Assembly
Tester Connection Condition Specified Condition
H66-12 (B42) - H1-4 (+B1) Always Below 1 Ω
H66-24 (AC41) - H1-15 (ACC1) Always Below 1 Ω
H66-12 (B42) or H1-4 (+B1) - Body ground and other terminals Always 10 kΩ or higher
H66-24 (AC41) or H1-15 (ACC1) - Body ground and other terminals Always 10 kΩ or higher

Television Display Assembly (w/ Rear Seat Entertainment System)
Tester Connection Condition Specified Condition
H66-11 (B43) - R16-1 (+B) Always Below 1 Ω
H66-24 (AC41) - R16-2 (ACC) Always Below 1 Ω
H66-11 (B43) or R16-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
H66-24 (AC41) or R16-2 (ACC) - Body ground and other terminals Always 10 kΩ or higher

Inner Rear View Mirror Assembly (w/ EC Mirror or Digital Inner Mirror)
Tester Connection Condition Specified Condition
H66-3 (IG41) - R1-1 (IG) Always Below 1 Ω
H66-3 (IG41) or R1-1 (IG) - Body ground and other terminals Always 10 kΩ or higher

Navigation ECU (w/ Navigation System)
Tester Connection Condition Specified Condition
H66-2 (B41) - H18-10 (+B) Always Below 1 Ω
H66-2 (B41) or H18-10 (+B) - Body ground and other terminals Always 10 kΩ or higher

Front Door Ambient Light LH (Front Door Trim Board Sub-assembly LH) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - J26-2 (+) Always Below 1 Ω
H66-11 (B43) or J26-2 (+) - Body ground and other terminals Always 10 kΩ or higher

Front Door Ambient Light RH (Front Door Trim Board Sub-assembly RH) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - J10-2 (+) Always Below 1 Ω
H66-11 (B43) or J10-2 (+) - Body ground and other terminals Always 10 kΩ or higher

Rear Door Ambient Light LH (Rear Door Trim Board Sub-assembly LH) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - K10-2 (+) Always Below 1 Ω
H66-11 (B43) or K10-2 (+) - Body ground and other terminals Always 10 kΩ or higher

Rear Door Ambientn Light RH (Rear Door Trim Board Sub-assembly RH) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - K5-2 (+) Always Below 1 Ω
H66-11 (B43) or K5-2 (+) - Body ground and other terminals Always 10 kΩ or higher

Front Passenger Side Tray Illumination Light (No. 1 Instrument Panel Light Sub-assembly) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - H69-2 (ILL+) Always Below 1 Ω
H66-11 (B43) or H69-2 (ILL+) - Body ground and other terminals Always 10 kΩ or higher

Center Tray Illumination Light (No. 1 Instrument Panel Light Sub-assembly) (w/ Ambient Illumination Light)
Tester Connection Condition Specified Condition
H66-11 (B43) - H68-2 (ILL+) Always Below 1 Ω
H66-11 (B43) or H68-2 (ILL+) - Body ground and other terminals Always 10 kΩ or higher

Air Conditioning Control Assembly
Tester Connection Condition Specified Condition
H66-25 (IL41) - H27-1 (ILL+) Always Below 1 Ω
H66-3 (IG41) - H27-6 (IG+) Always Below 1 Ω
H66-25 (IL41) or H27-1 (ILL+) - Body ground and other terminals Always 10 kΩ or higher
H66-3 (IG41) or H27-6 (IG+) - Body ground and other terminals Always 10 kΩ or higher

Central Gateway ECU (Network Gateway ECU)
Tester Connection Condition Specified Condition
H66-3 (IG41) - H59-11 (IG1) Always Below 1 Ω
H66-3 (IG41) or H59-11 (IG1) - Body ground and other terminals Always 10 kΩ or higher

Millimeter Wave Radar Sensor Assembly
Tester Connection Condition Specified Condition
H66-3 (IG41) - B6-8 (IGB) Always Below 1 Ω
H66-3 (IG41) or B6-8 (IGB) - Body ground and other terminals Always 10 kΩ or higher

Clearance Warning ECU Assembly
Tester Connection Condition Specified Condition
H66-3 (IG41) - H46-1 (IG) Always Below 1 Ω
H66-3 (IG41) or H46-1 (IG) - Body ground and other terminals Always 10 kΩ or higher

Meter Mirror Assembly (w/ Headup Display)
Tester Connection Condition Specified Condition
H66-3 (IG41) - H31-1 (IG) Always Below 1 Ω
H66-2 (B41) - H31-2 (B) Always Below 1 Ω
H66-3 (IG41) or H31-1 (IG) - Body ground and other terminals Always 10 kΩ or higher
H66-2 (B41) or H31-2 (B) - Body ground and other terminals Always 10 kΩ or higher

Blind Spot Monitor Sensor LH
Tester Connection Condition Specified Condition
H66-3 (IG41) - M43-5 (BLB) Always Below 1 Ω
H66-3 (IG41) or M43-5 (BLB) - Body ground and other terminals Always 10 kΩ or higher

Blind Spot Monitor Sensor RH
Tester Connection Condition Specified Condition
H66-3 (IG41) - M2-5 (BRB) Always Below 1 Ω
H66-3 (IG41) or M2-5 (BRB) - Body ground and other terminals Always 10 kΩ or higher

No. 2 Air Conditioning Control Assembly
Tester Connection Condition Specified Condition
H66-3 (IG41) - T2-9 (IG) Always Below 1 Ω
H66-25 (IL41) - T2-10 (ILL+) Always Below 1 Ω
H66-3 (IG41) or T2-9 (IG) - Body ground and other terminals Always 10 kΩ or higher
H66-25 (IL41) or T2-10 (ILL+) - Body ground and other terminals Always 10 kΩ or higher

Fog Light Assembly
Tester Connection Condition Specified Condition
H66-2 (B41) - 2 (FOG FR relay) Always Below 1 Ω
H66-2 (B41) - 5 (FOG FR relay) Always Below 1 Ω
H66-2 (B41) or 2 (FOG FR relay) - Body ground and other terminals Always 10 kΩ or higher
H66-2 (B41) or 5 (FOG FR relay) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ENGINE STOP AND START ECU (OUTPUT VOLTAGE FOR EACH SYSTEM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ENGINE STOP AND START ECU (OUTPUT VOLTAGE FOR EACH SYSTEM)
a.

Disconnect the connector from the corresponding system ECU/sensor.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
H1-4 (+B1) - Body ground Always 10.5 to 16 V
H18-10 (+B)*1 - Body ground Always 10.5 to 16 V
H31-2 (B) - Body ground Always 10.5 to 16 V
R16-1 (+B)*2 - Body ground Always 10.5 to 16 V
R1-6 (+B)*3 - Body ground Always 10.5 to 16 V
J26-2 (+)*4 - Body ground Always 10.5 to 16 V
J10-2 (+)*4 - Body ground Always 10.5 to 16 V
K10-2 (+)*4 - Body ground Always 10.5 to 16 V
K5-2 (+)*4 - Body ground Always 10.5 to 16 V
H69-2 (ILL+)*4 - Body ground Always 10.5 to 16 V
H68-2 (ILL+)*4 - Body ground Always 10.5 to 16 V
2 (FOG FR relay) - Body ground Always 10.5 to 16 V
5 (FOG FR relay) - Body ground Always 10.5 to 16 V


*1: w/ Navigation System

*2: w/ Rear Seat Entertainment System

*3: w/ EC Mirror or Digital Inner Mirror

*4: w/ Ambient Illumination Light



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
H1-15 (ACC1) - Body ground Ignition switch ACC 10.5 to 16 V
R16-2 (ACC)* - Body ground Ignition switch ACC 10.5 to 16 V


*: w/ Rear Seat Entertainment System



e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

HINT:

Measure the voltage at the corresponding terminals.


Standard Voltage:
Tester Connection Condition Specified Condition
A39-45 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
H57-9 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
H21-39 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
C67-4 (IG) - Body ground Ignition switch ON 10.5 to 16 V
R1-1 (IG)*1 - Body ground Ignition switch ON 10.5 to 16 V
H27-6 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
H59-11 (IG1) - Body ground Ignition switch ON 10.5 to 16 V
B6-8 (IGB) - Body ground Ignition switch ON 10.5 to 16 V
H46-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V
H31-1 (IG)*2 - Body ground Ignition switch ON 10.5 to 16 V
M43-5 (BLB) - Body ground Ignition switch ON 10.5 to 16 V
M2-5 (BRB) - Body ground Ignition switch ON 10.5 to 16 V
T2-9 (IG) - Body ground Ignition switch ON 10.5 to 16 V


*1: w/ EC Mirror or Digital Inner Mirror

*2: w/ Headup Display



Result:
Proceed to
OK
NG



OK

CHECK POWER SOURCE CIRCUIT (POWER SOURCE CIRCUIT OF RELATED SYSTEM)

NG

7.CHECK AUDIO SYSTEM
a.

Turn the ignition switch off and wait for 1 minute.


b.

Turn the ignition switch to ON.


c.

Lower the audio volume.


d.

Check if the audio system operates normally.

OK:

Audio system operates normally.



Result:
Proceed to
OK
NG



OK

END

NG

8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-12 (B42) or H1-4 (+B1) - Body ground Always 10 kΩ or higher



Result:
Result Proceed to
OK (Audio and visual system) A
OK (w/ Navigation system without Stereo Component Amplifier Assembly) B
OK (w/ Navigation system and Stereo Component Amplifier Assembly) C
NG D



A

B

C

9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the stereo component amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A18-5 (BO1) or M37-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
A18-12 (ACO) or M38-12 (ACC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BIN TERMINAL POWER SOURCE CIRCUIT)
A331558C47
1.5,0.167 1.917,0.417 0.417,0.25 2.031,1.885 2.031,1.406 true 1.948,1.917 2.406,2.115 0.458,0.198 10 false BIN 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.583,0.208 1.896,0.406 0.313,0.198 10 false A18
*a Front view of wire harness connector
(to External Backup Boost Converter (Eco Run Vehicle Converter Assembly))


a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A18-11 (BIN) - Body ground Always 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BATTERY)

11.CHECK HARNESS AND CONNECTOR (ACC TERMINAL POWER SOURCE CIRCUIT)
A331558C48
1.479,0.167 1.896,0.417 0.417,0.25 1.146,1.875 1.542,1.198 true 1,1.927 1.458,2.125 0.458,0.198 10 false ACC 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.563,0.208 1.875,0.406 0.313,0.198 10 false A18
*a Front view of wire harness connector
(to External Backup Boost Converter (Eco Run Vehicle Converter Assembly))


a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Turn the ignition switch to ACC.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A18-3 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V



d.

Turn the engine switch off.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A18-3 (ACC) - Body ground Ignition switch off 0 to 1 V



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)

NG

15.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
12.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - BODY GROUND)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A18-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - STEREO COMPONENT AMPLIFIER ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the stereo component amplifier assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A18-5 (BO1) - M37-1 (+B) Always Below 1 Ω
A18-12 (ACO) - M38-12 (ACC) Always Below 1 Ω
A18-5 (BO1) or M37-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
A18-12 (ACO) or M38-12 (ACC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the stereo component amplifier assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M37-1 (+B) - Body ground Always 10.5 to 16 V



c.

Turn the ignition switch to ACC.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M38-12 (ACC) - Body ground Ignition switch ACC 10.5 to 16 V



Result:
Proceed to
OK
NG



OK

NG

REPLACE ECO RUN VEHICLE CONVERTER ASSEMBLY (EXTERNAL BACKUP BOOST CONVERTER)

15.CHECK HARNESS AND CONNECTOR (EXTERNAL BACKUP BOOST CONVERTER (ECO RUN VEHICLE CONVERTER ASSEMBLY) - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the external backup boost converter (eco run vehicle converter assembly) connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Disconnect the engine stop and start ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A18-3 (ACC) - 4A-40 Always Below 1 Ω
A18-3 (ACC) or 4A-40 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR