Home › Vehicle Exterior › VEHICLE PROXIMITY NOTIFICATION SYSTEM › VEHICLE PROXIMITY NOTIFICATION SYSTEM › from 2020.11
RM37A0E _59 Vehicle Exterior _094410 VEHICLE PROXIMITY NOTIFICATION SYSTEM _0448770 VEHICLE PROXIMITY NOTIFICATION SYSTEM J

VEHICLE PROXIMITY NOTIFICATION SYSTEM  VEHICLE PROXIMITY NOTIFICATION SYSTEM  There is No Sound Made  


DESCRIPTION

Based on signals received from each ECU, the vehicle approaching speaker controller outputs warning sounds through the vehicle approaching speaker assembly.

WIRING DIAGRAM

E402275E67
5.656,5.76 6.948,6.25 1.292,0.49 10 false Vehicle Approaching Speaker Assembly 4.5,4.958 4.958,5.156 0.458,0.198 10 false SP+ 4.5,5.25 4.958,5.448 0.458,0.198 10 false SP- 4.469,6.969 4.927,7.167 0.458,0.198 10 false GND 3.521,7.792 4.833,8.281 1.313,0.49 10 false Vehicle Approaching Speaker Controller 0.708,7.49 2.656,7.792 1.948,0.302 10 false Combination Meter Assembly 0.854,2.396 3.521,2.615 2.667,0.219 10 false Hybrid Vehicle Control ECU 0.844,4.083 2.5,4.594 1.656,0.51 10 false Main Body ECU (Multiplex Network Body ECU) 0.719,5.792 2.625,6.302 1.906,0.51 10 false No. 2 Skid Control ECU (Brake Actuator Assembly) 1.927,0.896 3.021,1.104 1.094,0.208 10 false ECU-IG1 NO. 3 0.167,0.729 1.656,1 1.49,0.271 10 false from IG1-NO. 1 Relay 3.552,0.75 4.01,0.948 0.458,0.198 10 false IG 1.479,8.427 3.323,8.635 1.844,0.208 10 false : CAN Communication Line 3.354,0.615 3.51,0.813 0.156,0.198 10 false 1 4.885,4.844 5.042,5.042 0.156,0.198 10 false 7 4.885,5.135 5.042,5.333 0.156,0.198 10 false 8 4.875,6.833 5.031,7.031 0.156,0.198 10 false 6 6.01,5.135 6.167,5.333 0.156,0.198 10 false 1 6.01,4.844 6.167,5.042 0.156,0.198 10 false 2 5.656,5.594 6.115,5.792 0.458,0.198 10 false A12 3.521,7.625 3.979,7.823 0.458,0.198 10 false A50

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle proximity notification system uses the CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting.

Click hereVehicle Exterior>VEHICLE PROXIMITY NOTIFICATION SYSTEM>VEHICLE PROXIMITY NOTIFICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Vehicle Proximity Notification System > Trouble Codes
50001 393

Result:
Result Proceed to
DTC B1350 is not output A
DTC B1350 is output B



A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Perform the Active Test according to the display on the GTS.

Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Proximity Sound (Vehicle Stationary) 0 km/h (0 mph) vehicle proximity warning sound OFF or ON -
Body Electrical > Vehicle Proximity Notification System > Active Test
Tester Display
Proximity Sound (Vehicle Stationary)
50004 393 2

Result:
Result Proceed to
The warning sound is produced A
The warning sound is not produced B



A

B

3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (VEHICLE APPROACHING SPEAKER CONTROLLER - POWER SOURCE AND BODY GROUND)
a.

Disconnect the A50 vehicle approaching speaker controller connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A50-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR