The main body ECU (multiplex network body ECU) controls the operation of the following lights:
Center Tray Illumination Light (No. 1 Instrument Panel Light Sub-assembly)
Front Passenger Side Tray Illumination Light (No. 1 Instrument Panel Light Sub-assembly)
Front Door Ambient Light LH (Front Door Trim Board Sub-assembly LH)
Front Door Ambient Light RH (Front Door Trim Board Sub-assembly RH)
Rear Door Ambient Light LH (Rear Door Trim Board Sub-assembly LH)
Rear Door Ambient Light RH (Rear Door Trim Board Sub-assembly RH)
Inspect the fuses for circuits related to this system before performing the following procedure.
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
The auxiliary battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
| Result | Proceed to |
|---|---|
| w/o Stop and Start System | A |
| w/ Stop and Start System | B |
A
B
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Interior Illumination Light1 | ·
Center tray illumination light (No. 1 instrument panel light sub-assembly) ·
Front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) ·
Door ambient light (Door trim board sub-assembly) |
OFF or ON | Preconditions for using the Active Test to check dimmer controlled illumination:
·
Ignition switch ON ·
Shift lever is in any position other than P |
| Tester Display |
|---|
| Interior Illumination Light1 |
Center tray illumination light, front passenger side tray illumination light and door ambient lights come on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Center tray illumination light does not come on) | B |
| NG (Front passenger side tray illumination light does not come on) | C |
| NG (Front door ambient light LH does not come on) | D |
| NG (Front door ambient light RH does not come on) | E |
| NG (Rear door ambient light LH does not come on) | F |
| NG (Rear door ambient light RH does not come on) | G |
| NG (Center tray illumination light, front passenger side tray illumination light and door ambient lights do not come on) | H |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
F
G
H
Click hereVehicle Interior>LIGHTING (INT)>INTERIOR ILLUMINATION LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - H68-2 (ILL+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>INTERIOR ILLUMINATION LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H69-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - H69-2 (ILL+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Front Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J26-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - J26-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Front Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - J10-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Rear Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - K10-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Rear Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - K5-2 (+) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the 4F instrument panel junction block assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
|
*1: for Gasoline Model *2: for HV Model |
||
| 4F-1 - Body ground | Always*1
Ignition switch off*2 |
11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Disconnect the 4B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4F-1 - 4B-24 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H68 center tray illumination light (No. 1 instrument panel light sub-assembly) connector.
Disconnect the H69 front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) connector.
Disconnect the J26 front door ambient light LH (front door trim board sub-assembly LH) connector.
Disconnect the J10 front door ambient light RH (front door trim board sub-assembly RH) connector.
Disconnect the K10 rear door ambient light LH (rear door trim board sub-assembly LH) connector.
Disconnect the K5 rear door ambient light RH (rear door trim board sub-assembly RH) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4B-24 - H68-2 (ILL+) | Always | Below 1 Ω |
| 4B-24 - H69-2 (ILL+) | Always | Below 1 Ω |
| 4B-24 - J26-2 (+) | Always | Below 1 Ω |
| 4B-24 - J10-2 (+) | Always | Below 1 Ω |
| 4B-24 - K10-2 (+) | Always | Below 1 Ω |
| 4B-24 - K5-2 (+) | Always | Below 1 Ω |
| 4B-24 - Body ground | Always | 10 kΩ or higher |
| H68-2 (ILL+) - Body ground | Always | 10 kΩ or higher |
| H69-2 (ILL+) - Body ground | Always | 10 kΩ or higher |
| J26-2 (+) - Body ground | Always | 10 kΩ or higher |
| J10-2 (+) - Body ground | Always | 10 kΩ or higher |
| K10-2 (+) - Body ground | Always | 10 kΩ or higher |
| K5-2 (+) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| H69-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| J26-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| J10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| K10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| K5-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| H68-1 (ILL-) - Body ground | Always | 10 kΩ or higher |
| H69-1 (ILL-) - Body ground | Always | 10 kΩ or higher |
| J26-1 (-) - Body ground | Always | 10 kΩ or higher |
| J10-1 (-) - Body ground | Always | 10 kΩ or higher |
| K10-1 (-) - Body ground | Always | 10 kΩ or higher |
| K5-1 (-) - Body ground | Always | 10 kΩ or higher |
| H44-20 (LED1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Interior Illumination Light1 | ·
Center tray illumination light (No. 1 instrument panel light sub-assembly) ·
Front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) ·
Door ambient light (Door trim board sub-assembly) |
OFF or ON | Preconditions for using the Active Test to check dimmer controlled illumination:
·
Ignition switch ON ·
Shift lever is in any position other than P |
| Tester Display |
|---|
| Interior Illumination Light1 |
Center tray illumination light, front passenger side tray illumination light and door ambient lights come on.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Center tray illumination light does not come on) | B |
| NG (Front passenger side tray illumination light does not come on) | C |
| NG (Front door ambient light LH does not come on) | D |
| NG (Front door ambient light RH does not come on) | E |
| NG (Rear door ambient light LH does not come on) | F |
| NG (Rear door ambient light RH does not come on) | G |
| NG (Center tray illumination light, front passenger side tray illumination light and door ambient lights do not come on) | H |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
D
E
F
G
H
Click hereVehicle Interior>LIGHTING (INT)>INTERIOR ILLUMINATION LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-2 (ILL+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>INTERIOR ILLUMINATION LIGHT>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H69-2 (ILL+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H69-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Front Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J26-2 (+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J26-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Front Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-2 (+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Rear Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-2 (+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Interior>LIGHTING (INT)>AMBIENT LIGHT (for Rear Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-2 (+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the H68 center tray illumination light (No. 1 instrument panel light sub-assembly) connector.
Disconnect the H69 front passenger side tray illumination light (No. 1 instrument panel light sub-assembly) connector.
Disconnect the J26 front door ambient light LH (front door trim board sub-assembly LH) connector.
Disconnect the J10 front door ambient light RH (front door trim board sub-assembly RH) connector.
Disconnect the K10 rear door ambient light LH (rear door trim board sub-assembly LH) connector.
Disconnect the K5 rear door ambient light RH (rear door trim board sub-assembly RH) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-2 (ILL+) - Body ground | Always | 10.5 to 16 V |
| H69-2 (ILL+) - Body ground | Always | 10.5 to 16 V |
| J26-2 (+) - Body ground | Always | 10.5 to 16 V |
| J10-2 (+) - Body ground | Always | 10.5 to 16 V |
| K10-2 (+) - Body ground | Always | 10.5 to 16 V |
| K5-2 (+) - Body ground | Always | 10.5 to 16 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the H44 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H68-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| H69-1 (ILL-) - H44-20 (LED1) | Always | Below 1 Ω |
| J26-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| J10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| K10-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| K5-1 (-) - H44-20 (LED1) | Always | Below 1 Ω |
| H68-1 (ILL-) - Body ground | Always | 10 kΩ or higher |
| H69-1 (ILL-) - Body ground | Always | 10 kΩ or higher |
| J26-1 (-) - Body ground | Always | 10 kΩ or higher |
| J10-1 (-) - Body ground | Always | 10 kΩ or higher |
| K10-1 (-) - Body ground | Always | 10 kΩ or higher |
| K5-1 (-) - Body ground | Always | 10 kΩ or higher |
| H44-20 (LED1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG