The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during main body ECU removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.
1. DISCHARGE DOOR CONTROL BATTERY AND DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ Door Control Battery)
Always ensure that the cable is disconnected from the negative (-) auxiliary battery terminal and the door control battery is fully discharged when removing or installing the instrument panel junction block assembly with main body ECU.
Make sure to perform the following procedure before removal and installation of the instrument panel junction block assembly with main body ECU.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
When turning the ignition switch off after the door control battery is fully charged, the door control battery becomes completely discharged due to self-discharge within approximately 30 minutes.
Approximately 90 seconds after the ignition switch is on (IG), the door control battery becomes fully charged.
When approximately 30 minutes or more have elapsed after the ignition switch off, the Active Test may not be able to be performed.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
| Tester Display | Control Range |
|---|---|
| Shock Detection Unlock | ON/OFF |
Do not perform the Active Test at this time.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Perform the "Shock Detection Unlock" Active Test repeatedly until the multiplex network body ECU (main body ECU) communication lost error message "Lost communication with vehicle" is displayed on the GTS.
| Tester Display |
|---|
| Shock Detection Unlock |
When the cable is disconnected from the negative (-) auxiliary battery terminal and the door control battery becomes completely discharged, the main body ECU (multiplex network body ECU) communication lost message "Lost communication with vehicle" is displayed on the GTS.
The number of times the Active Test can be performed depends on the charge condition of the door control battery.
2.REMOVE INSTRUMENT PANEL SAFETY PAD (for LHD)
55308B
3.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY (for LHD)
82878
4.REMOVE ECU INTEGRATION BOX LH (for LHD)
5.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for LHD)
Disconnect each connector.
Disengage the 3 clamps.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.
|
Remove in this Direction |
Using a screwdriver, disengage the claw as shown in the illustration.
|
Remove in this Direction |
Using a screwdriver, disengage the claw as shown in the illustration.
Disengage the 2 guides.
Remove the 2 nuts.
Pull out the instrument panel junction block assembly with main body ECU.
Disengage the clamp.
|
Remove in this Direction |
Disengage the clamp.
Disengage the 2 claws and raise the 2 lock levers to disconnect the 2 connectors as shown in the illustration and remove the instrument panel junction block assembly with main body ECU.
6.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for LHD)
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push in this Direction |
Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.
| *a | Protective Tape |
|
Insert in this Direction |
|
Remove in this Direction |
With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.
Do not touch the main body ECU (multiplex network body ECU) connector.
67914
7.REMOVE FRONT DOOR SCUFF PLATE LH (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62112A
8.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62312B
9.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55436A
10.REMOVE INSTRUMENT PANEL FINISH END PANEL LH (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55607
11.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
55303B
12.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (for RHD)
Use the same procedure for the RHD and LHD.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL
13.REMOVE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY WITH MAIN BODY ECU (for RHD)
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.
Disengage the clamp.
Disconnect each connector.
Disengage the clamp.
Disconnect the 3 connectors.
Disengage the clamp.
Remove the bolt and nut.
Disengage the 3 clamps.
|
Remove in this Direction |
Disengage the 2 claws and pull down the 2 lock levers to disconnect the 2 connectors as shown in the illustration.
Disengage the 4 claws to remove the instrument panel junction block assembly with main body ECU as shown in the illustration.
|
Remove in this Direction | - | - |
82673C
14.REMOVE JUNCTION BLOCK BRACKET (for RHD)
Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the junction block bracket.
| *a | Protective Tape | - | - |
15.REMOVE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (for RHD)
| *1 | Instrument Panel Junction Block Assembly |
| *2 | Main Body ECU (Multiplex Network Body ECU) |
|
Push in this Direction |
Press the claw of the instrument panel junction block assembly as shown in the illustration to release the lock.
| *a | Protective Tape |
|
Insert in this Direction |
|
Remove in this Direction |
With the instrument panel junction block assembly lock released, insert a screwdriver with its tip wrapped with protective tape horizontally between the main body ECU (multiplex network body ECU) and instrument panel junction block assembly.
Use a screwdriver with a diameter between 5.0 mm (0.197 in.) and 6.3 mm (0.248 in.) and a length of approximately 90 mm (3.54 in.).
Do not insert the screwdriver under the connector socket of the main body ECU (multiplex network body ECU).
Using the screwdriver, carefully raise the main body ECU (multiplex network body ECU) to the position where the connector becomes disconnected.
Do not twist the screwdriver to raise the main body ECU (multiplex network body ECU).
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
Raise the main body ECU (multiplex network body ECU) as shown by the arrow (1), and then pull it out as shown by the arrow (2) in the illustration.
Do not touch the main body ECU (multiplex network body ECU) connector.