Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for RHD) › from 2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0449077 BRAKE MASTER CYLINDER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake master cylinder sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*: Learning can also be performed using the GTS.

Click here(Click here)

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal.


PROCEDURE

Hide 1.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 53808A 2.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 3.REMOVE FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 4.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 5.REMOVE FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53608A 6.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 7.REMOVE FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 55704B 8.REMOVE COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 9.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 47234L 10.DISCONNECT NO. 1 RESERVOIR HOSE

a.
C447360

Slide the clip and disconnect the No. 1 reservoir hose from the brake master cylinder sub-assembly.


Hide 47201 11.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

a.
C447361

Using a union nut wrench, disconnect the 2 brake lines from the brake master cylinder sub-assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




b.
C447362

Remove the 2 nuts and brake master cylinder sub-assembly from the brake booster assembly.

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.




Hide 47201B 12.REMOVE BRAKE MASTER CYLINDER O-RING

a.

Remove the brake master cylinder O-ring from the brake master cylinder sub-assembly.