Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (for RHD) › from 2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0449077 BRAKE MASTER CYLINDER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(for RHD)  INSTALLATION  


PROCEDURE

Hide 47201B 1.INSTALL BRAKE MASTER CYLINDER O-RING

a.

Install a new brake master cylinder O-ring to the brake master cylinder sub-assembly.


Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

NOTICE:

When installing a new brake master cylinder sub-assembly, remove the protectors from the master cylinder piston and outlet ports.


a.

Install the brake master cylinder sub-assembly to the brake booster assembly with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:
·

The brake master cylinder sub-assembly requires careful handling. Do not drop or subject the brake master cylinder sub-assembly to any impact. Do not reuse a brake master cylinder sub-assembly that has been dropped.

·

Do not hold the brake master cylinder sub-assembly by the master cylinder piston. Hold the brake master cylinder sub-assembly by its body or its reservoir when carrying it.

·

Do not pull out the master cylinder piston.

·

Do not strike or pinch the master cylinder piston, or cause any damage to the master cylinder piston by any other means.

·

When installing the brake master cylinder sub-assembly to the brake booster assembly, or when removing the brake master cylinder sub-assembly from the brake booster assembly, make sure that the brake master cylinder sub-assembly is kept horizontal or with its tip facing downward (the master cylinder piston is facing upward) to prevent the master cylinder piston from falling out.

·

Do not allow any foreign matter to contaminate the master cylinder piston. If any foreign matter gets on the master cylinder piston, remove it by using a piece of new and dry cloth. Do not use water or detergent. Then apply an even layer of lithium soap base glycol grease around the circumference (sliding part) of the master cylinder piston.

·

Do not use any other types of grease.

·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




b.
C447366C01
2.885,2.896 2.708,2.896 2.708,2.896 2.708,2.646 false 1.792,2.927 2.104,3.083 0.313,0.156 10 false *a 2.906,2.823 3.219,2.979 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, connect the 2 brake lines to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow the brake lines to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 47234L 3.CONNECT NO. 1 RESERVOIR HOSE

a.

Connect the No. 1 reservoir hose to the brake master cylinder sub-assembly, and slide the clip to secure it.


Hide 55704B 5.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 53608A 6.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 7.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 8.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 9.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 10.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 11.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 12.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY