Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP (for RHD) › from 2020.11
RM37A0E _54 Brake _086869 BRAKE SYSTEM (OTHER) _0449419 BRAKE BOOSTER PUMP(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP(for RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
C447708C01
1.135,1.448 0.979,1.24 false 2.292,0.417 2.479,0.271 false 2.177,0.906 2.479,1.031 false 2.094,1.958 2.5,1.958 false 0.813,1.146 1.125,1.302 0.313,0.156 10 false *a 2.521,0.167 2.833,0.323 0.313,0.156 10 false *b 2.521,0.958 2.833,1.115 0.313,0.156 10 false *c 2.552,1.885 2.865,2.042 0.313,0.156 10 false *d
*a Union
*b Connector
*c Wire Harness
*d Stud


Do not carry the brake booster with accumulator pump assembly by the parts shown in the illustration.


PROCEDURE

Hide 47381 1.INSTALL NO. 1 BRAKE TUBE CLAMP BRACKET

a.

Install the No. 1 brake tube clamp bracket to the brake booster with accumulator pump assembly with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 47070B 2.INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

a.
C447829C01
0.823,0.375 0.99,0.375 0.99,0.375 0.99,0.708 false 0.375,1.542 0.458,1.542 0.458,1.542 0.458,1.792 false 0.25,1.927 0.25,2.26 false 2.323,0.5 2.823,0.5 false 2.865,3.073 2.865,2.656 true 2.323,2.125 2.594,2.406 true 2.125,0.417 2.438,0.573 0.313,0.156 10 false *1 0.656,0.292 0.969,0.448 0.313,0.156 10 false *2 0.208,1.469 0.521,1.625 0.313,0.156 10 false *3 0.188,2.281 0.5,2.438 0.313,0.156 10 false *4 2.792,3.073 3.073,3.281 0.281,0.208 10 false *a 2.156,2.031 2.49,2.406 0.333,0.375 10 false *b
*1 Brake Booster with Accumulator Pump Assembly
*2 Brake Actuator with Bracket
*3 Brake Traction Actuator Bracket Bushing
*4 No. 1 Brake Actuator Case Collar
*a Pin
*b Bushing


Install the brake booster with accumulator pump assembly, brake traction actuator bracket bushing and No. 1 brake actuator case collar to the brake actuator with bracket.

NOTICE:
·

Be careful not to allow brake fluid to enter the connector.

·

Make sure that the pins of the brake actuator with bracket are inserted into each center of the bushings of the brake booster with accumulator pump assembly.

·

If installing a new brake booster with accumulator pump assembly, do not remove the hole plugs before connecting the brake lines because the brake booster with accumulator pump assembly is filled with brake fluid.




b.
C450314

Install the nut.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


c.
C447706N01
0.948,0.583 1.104,0.781 0.156,0.198 10 false 1 1.156,1.24 1.313,1.438 0.156,0.198 10 false 2

Engage the 2 clamps to install the wire harness to the brake actuator with bracket in the order shown in the illustration.


Hide 3.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY