Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for HV Model RHD) › from 2020.11
RM37A0E _54 Brake _086868 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0449071 BRAKE ACTUATOR(for HV Model RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for HV Model RHD)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

The parking brake indicator light (red) blinks when the ignition switch is turned to ON after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.


PROCEDURE

Hide 44547B 1.INSTALL BRAKE ACTUATOR BRACKET CUSHION

HINT:

Perform this procedure only when replacement of the brake actuator bracket cushions is necessary.


a.

Install the 3 brake actuator bracket cushions to the lower brake actuator bracket.


Hide 44521B 2.INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

HINT:

Perform this procedure only when replacement of the No. 2 brake actuator case collars is necessary.


a.

Install the 3 No. 2 brake actuator case collars to the brake actuator bracket cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bracket cushion.



b.

Install the upper brake actuator bracket to the lower brake actuator bracket with the 3 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 44510 3.INSTALL BRAKE ACTUATOR ASSEMBLY

a.
C447710N01
1.167,1.292 1.313,1.49 0.146,0.198 10 true 1 2.875,1.167 3.042,1.333 0.167,0.167 10 true 2 1.844,1.896 1.99,2.073 0.146,0.177 10 true 3

Install the brake actuator assembly to the brake actuator bracket assembly with the 3 bolts in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·
C447709

Do not hold the brake actuator assembly by the connector.




Hide 47070B 4.INSTALL BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

Hide 5.INSTALL BRAKE ACTUATOR WITH BRAKE BOOSTER PUMP ASSEMBLY

a.

Temporarily install the brake actuator with brake booster pump assembly to its original position.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Hold the brake actuator with brake booster pump assembly by the brake actuator bracket assembly.



HINT:

Install the brake actuator with brake booster pump assembly while avoiding the brake lines.



b.

Connect the No. 2 brake actuator hose, and slide the clip to secure it as shown in the illustration.

C447831C01
3.823,0.396 3.604,0.635 true 5.969,1.521 5.615,1.354 false 6.406,0.573 6.104,0.365 true 5.969,1.115 6.333,1.135 true 5.938,0.271 6.25,0.427 0.313,0.156 10 false *a 3.844,0.302 4.042,0.49 0.198,0.188 10 true *b 5.448,1.26 5.76,1.417 0.313,0.156 10 false *c 6.729,0.51 7.042,0.667 0.313,0.156 10 false *d 6.521,0.854 6.833,1.01 0.313,0.156 10 false *e 6.521,0.219 6.833,0.375 0.313,0.156 10 false *e 6.375,1.052 6.688,1.208 0.313,0.156 10 false *a
*a Paint Mark (A) *b Paint Mark (B)
*c Rib *d Center of Rib
*e Within 90° - -
V100136

Left Side of the Vehicle - -



c.
C447830C01
2.75,2.771 2.75,3.021 false 1.823,3.021 2.135,3.177 0.313,0.156 10 false *a 2.708,3.031 3.021,3.188 0.313,0.156 10 false *b 1.063,1.75 1.208,1.938 0.146,0.188 10 true A 1.396,2.01 1.531,2.177 0.135,0.167 10 true B
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Tighten the bolt (A).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


d.

Using a union nut wrench, tighten the bolt (B).

Torque:
Specified tightening torque : 19 N*m (194 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

16.9 N*m (172 kgf*cm, 12 ft.*lbf)




e.

Tighten the nut.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


f.
C447832C01
2.75,3.042 2.75,2.708 false 1.823,2.958 2.042,3.135 0.219,0.177 10 false *a 2.698,3.052 3.01,3.208 0.313,0.156 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Temporarily tighten the brake line to the brake booster with accumulator pump assembly.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




g.

Using a union nut wrench, fully tighten the brake line.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.

Install the brake line with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


i.
C447702

Engage the clamp to install a new No. 10 brake tube clamp.


j.

Return the brake line to its original position.

NOTICE:

Do not apply excessive force to the brake line.



k.
C447699

Engage the clamp to install brake line.

NOTICE:

Do not kink or damage the brake line.



l.
C447698C01
2.51,1.26 2.594,0.875 false 3.073,1.25 3,0.875 false 2.406,1.271 2.625,1.458 0.219,0.188 10 false *b 3.021,1.281 3.208,1.469 0.188,0.188 10 false *a
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly


Engage the 2 clamps to install a new No. 12 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.



m.
C447697C01
2.938,0.99 3.083,0.646 true 3.063,1.688 2.938,1.365 true 2.625,0.813 2.469,0.469 true 2.438,1.052 2.615,1.083 true 2.5,1.667 2.656,1.354 true 3.115,0.5 3.333,0.667 0.219,0.167 10 false *b 3.115,1.625 3.427,1.781 0.313,0.156 10 false *a 2.313,0.375 2.625,0.531 0.313,0.156 10 false *c 2.281,0.969 2.594,1.125 0.313,0.156 10 false *d 2.323,1.594 2.635,1.75 0.313,0.156 10 false *e
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH
*d To Rear Disc Brake Cylinder Assembly RH
*e To Rear Disc Brake Cylinder Assembly LH


Engage the 5 clamps to install a new No. 1 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.



n.
C447696C01
0.781,0.99 1.052,0.99 true 0.781,0.708 1.063,0.708 true 0.542,0.563 0.406,0.375 true 0.521,0.792 0.344,0.792 true 0.531,1.01 0.354,1.01 true 1.104,0.906 1.417,1.063 0.313,0.156 10 false *a 1.104,0.635 1.417,0.792 0.313,0.156 10 false *b 0.25,0.271 0.563,0.427 0.313,0.156 10 false *c 0.198,0.708 0.51,0.865 0.313,0.156 10 false *d 0.198,0.927 0.51,1.083 0.313,0.156 10 false *e
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH
*d To Rear Disc Brake Cylinder Assembly RH
*e To Rear Disc Brake Cylinder Assembly LH


Engage the 5 clamps to install a new No. 4 brake tube clamp to the brake lines.

NOTICE:

Do not kink or damage the brake lines.



o.

Install a new No. 4 brake tube clamp with the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


p.
C447700

Temporarily tighten the brake line to the front flexible hose.

NOTICE:
·

Do not kink or damage the brake line.

·

Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.




q.
C447694C01
1.958,0.625 2.156,0.375 true 1.75,0.865 1.813,1.208 true 1.458,1.719 1.656,1.469 true 1.229,1.375 1.521,0.958 true 1.01,0.906 1.302,0.75 true 2.25,1.167 2.583,0.75 2.583,0.75 2.833,0.75 true 2.875,0.656 3.083,0.833 0.208,0.177 10 true *b 1.344,1.74 1.521,1.927 0.177,0.188 10 true *a 0.771,0.833 0.99,1.01 0.219,0.177 10 true *c 1.083,1.396 1.292,1.573 0.208,0.177 10 true *d 1.75,1.24 1.958,1.417 0.208,0.177 10 true *e 2.177,0.281 2.354,0.448 0.177,0.167 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Disc Brake Cylinder Assembly RH
*d To Front Disc Brake Cylinder Assembly LH
*e To Rear Disc Brake Cylinder Assembly RH
*f To Rear Disc Brake Cylinder Assembly LH


Temporarily tighten the 6 brake lines to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




r.
C447834C01
2.729,3.031 2.729,2.698 false 1.833,2.99 2.146,3.146 0.313,0.156 10 false *a 2.667,3.052 2.885,3.229 0.219,0.177 10 true *b 0.885,1.125 1.021,1.271 0.135,0.146 10 true A 2.052,1.406 2.198,1.573 0.146,0.167 10 true B 1.604,1.083 1.729,1.24 0.125,0.156 10 true A 1.906,1 2.031,1.156 0.125,0.156 10 true A 2.271,0.51 2.396,0.667 0.125,0.156 10 true A 1.156,1.479 1.302,1.646 0.146,0.167 10 true B
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the 6 brake lines.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not kink or damage the brake lines.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

for Specified Tightening Torque (A):

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

for Specified Tightening Torque (B):

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

17.4 N*m (177 kgf*cm, 13 ft.*lbf)




s.
C447833C01
2.74,3.042 2.74,2.708 false 1.781,2.969 2.094,3.125 0.313,0.156 10 false *a 2.667,3.073 2.917,3.313 0.25,0.24 10 false *b
*a Torque Wrench Fulcrum Length
*b Union Nut Wrench


Using a union nut wrench, fully tighten the brake line while holding the front flexible hose with a wrench.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the brake line.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




t.
C447835C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the engine room main wire to the brake actuator assembly and lock the lock lever as shown in the illustration.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the connector can be connected smoothly.

·

Be careful not to allow any brake fluid to enter the connector.




u.
C447841

Connect the engine room main wire to the brake booster with accumulator pump assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



Hide 44551C 6.BLEED NO. 1 BRAKE ACTUATOR TUBE

Hide 7.FILL RESERVOIR WITH BRAKE FLUID

Hide 8.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>A25A-FXS, A25B-FXS AUXILIARY BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 55704B 10.INSTALL COWL VENTILATOR PANEL SUB-ASSEMBLY

Hide 11.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY LH

Hide 53607B 12.INSTALL FRONT UPPER SUSPENSION TO COWL BRACE SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 53892C 13.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT LH

Hide 53891C 14.INSTALL FRONT FENDER SPLASH SHIELD SEAL FRONT RH

HINT:

Perform the same procedure as for the LH side.


Hide 53808A 15.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR LH

Hide 53807A 16.INSTALL FENDER SPLASH SHIELD SUB-ASSEMBLY REAR RH

HINT:

Perform the same procedure as for the LH side.


Hide 17.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 19.INSTALL FRONT WHEEL LH

Hide 20.PERFORM INITIALIZATION AND CALIBRATION