Home › Drivetrain › UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH › from 2020.11
RM37A0E _52 Drivetrain _094409 UA80E AUTOMATIC TRANSMISSION / TRANSAXLE _0449680 PARK / NEUTRAL POSITION SWITCH N

UA80E AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  ADJUSTMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during park/neutral position switch assembly adjustment are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: Learning can also be performed using the GTS.

Click here(Click here)

*2: Not necessary when ECM replaced with new one

Battery terminal is disconnected/reconnected Idle the engine for approximately 5 to 60 minutes or drive the vehicle until stop and start control is permitted Stop and Start System (Click here)
Perform steering sensor zero point calibration Lane Control System (Click here)
Parking Support Brake System*1
Pre-collision System
Memorize steering angle neutral point Parking Assist Monitor System (Click here)
Panoramic View Monitor System (Click here)
Initialize back door lock Power Door Lock Control System (Click here)
Reset back door close position Power Back Door System (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration DTC is output (Click here)
Code registration Engine start function See Service Bulletin for the registration method
If transaxle compensation code read from ECM:
·

Perform reset memory*2

·

Transfer transaxle compensation code

·

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


for Initialization:
(Click here)
for Registration:
(Click here)
If transaxle compensation code not read from ECM:
·

Perform reset memory*2

·

Reset transaxle compensation code

·

Perform road test to allow ECM to learn


Replacement of battery
·

Integrated Current Value Initialization

·

Switch Battery Type


Stop and Start System (Click here)

NOTICE:
·

After the ignition switch is turned off, the radio and display receiver assembly or the radio receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.

·

If the ECM has been struck or dropped, replace it.

·

Perform Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION

·

Before adjusting the park/neutral position switch assembly, check that the shift lever is in N.



PROCEDURE

Hide 1.SECURE VEHICLE

a.

Fully apply the parking brake and chock a wheel.

CAUTION:
C332327

·

Make sure to apply the parking brake and chock a wheel before performing this procedure.

·

If the vehicle is not secure and the shift lever is moved to N, the vehicle may suddenly move, possibly resulting in an accident or serious injury.




Hide 33820B 2.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 84540 3.ADJUST PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C426638

Disengage the wire harness clamp.


b.
C426639

Disconnect the park/neutral position switch assembly connector.


c.
C426640

Remove the nut, washer and transmission control shaft lever from the manual valve lever shaft sub-assembly.


d.
C426641

Loosen the 2 bolts of the park/neutral position switch assembly.


e.
C426642C01
2.417,1.417 2.083,1.417 2.083,1.417 1.906,0.927 true 1.333,1.063 1.469,1.063 1.469,1.063 1.708,0.802 true 2.448,1.292 2.667,1.5 0.219,0.208 10 true *a 1.156,0.958 1.365,1.146 0.208,0.188 10 true *b
*a Neutral Basic Line
*b Protrusion


Align the protrusion with the neutral basic line.


f.

Hold the park/neutral position switch assembly in position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


g.

Install the transmission control shaft lever to the manual valve lever shaft sub-assembly with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


h.

Connect the park/neutral position switch assembly connector.


i.

Engage the wire harness clamp.


Hide 33820B 4.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 84540 5.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY OPERATION