Home › Vehicle Interior › HEATING / AIR CONDITIONING › FRONT EVAPORATOR TEMPERATURE SENSOR (for Gasoline Model) › from 2020.11
RM37A0E _58 Vehicle Interior _086896 HEATING / AIR CONDITIONING _0417378 FRONT EVAPORATOR TEMPERATURE SENSOR(for Gasoline Model) A

HEATING / AIR CONDITIONING  FRONT EVAPORATOR TEMPERATURE SENSOR(for Gasoline Model)  INSTALLATION  


PROCEDURE

Hide 88625 1.INSTALL NO. 1 COOLER THERMISTOR

a.

w/o Stop And Start System:

i.
E431762C01
0.927,0.458 1.719,0.969 true 2.406,0.667 2.177,1 true 1.948,2.75 2.594,4.292 true 2.167,2.75 2.948,4.188 true 2.635,4.219 2.885,4.427 0.25,0.208 10 false *a 2.99,4.083 3.25,4.302 0.26,0.219 10 false *b 0.792,0.354 0.99,0.542 0.198,0.188 10 false a 1.875,0.375 2.073,0.563 0.198,0.188 10 false X 0.292,3.052 0.49,3.24 0.198,0.188 10 false A 1.563,4.365 1.76,4.552 0.198,0.188 10 false B 2.469,0.552 2.667,0.74 0.198,0.188 10 false b
*a Securing Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 50.0 mm (1.97 in.)
B 61.1 mm (2.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





b.

w/ Stop And Start System:

i.
E455621C01
2.135,0.5 1.813,0.885 true 1,0.594 1.344,0.917 true 2.188,3.052 2.667,4.271 true 2.375,3.052 2.854,4.271 true 2.813,4.281 3.063,4.49 0.25,0.208 10 false *a 2.615,4.281 2.875,4.5 0.26,0.219 10 false *b 2.167,0.385 2.365,0.573 0.198,0.188 10 false a 1.573,0.313 1.771,0.5 0.198,0.188 10 false X 0.438,2.958 0.635,3.146 0.198,0.188 10 false A 0.875,0.49 1.073,0.677 0.198,0.188 10 false b 0.781,3.156 0.979,3.344 0.198,0.188 10 false B 1.531,4.021 1.729,4.208 0.198,0.188 10 false C 1.542,4.281 1.74,4.469 0.198,0.188 10 false D
*a Securing Part
*b Sensor Part


Install the No. 1 cooler thermistor as shown in the illustration.

Installation Position:
Part Length
A 50.0 mm (1.97 in.)
B 25.0 mm (0.984 in.)
C 54.4 mm (2.14 in.)
D 61.1 mm (2.41 in.)


NOTICE:
·

Be sure to insert the No. 1 cooler thermistor only once because reinserting it into the same position will not allow it to be firmly secured.

·

When reusing the No. 1 cooler evaporator sub-assembly, insert the No. 1 cooler thermistor one row next to the one that has been used previously (X in the illustration).

·

After inserting the No. 1 cooler thermistor, do not apply excessive force to the wire.

·

Directly insert the No. 1 cooler thermistor until the edge of the plastic case "a" comes into contact with the No. 1 cooler evaporator sub-assembly "b".





Hide 88501 2.INSTALL NO. 1 COOLER EVAPORATOR SUB-ASSEMBLY

Hide 87050C 8.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Single Type)

Hide 87050C 9.INSTALL NO. 1 AIR CONDITIONING RADIATOR DAMPER SERVO SUB-ASSEMBLY (for Dual Type)

Hide 87130D 11.INSTALL BLOWER ASSEMBLY