Home › Power Source / Network › 2GR-FKS (BATTERY / CHARGING) › CHARGING SYSTEM (w/ Stop And Start System) › from 2020.11
RM37A0E _57 Power Source / Network _086881 2GR-FKS BATTERY / CHARGING _0452458 CHARGING SYSTEM(w/ Stop And Start System) C

2GR-FKS BATTERY / CHARGING  CHARGING SYSTEM(w/ Stop And Start System)  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch to ON
(1 trip detection logic)
·

Wire harness or connector

·

generator assembly

·

ECM


Charge warning is not displayed DTC stored SAE Code: P161A

WIRING DIAGRAM

A413201E04
1.708,0.906 2.479,1.104 0.771,0.198 10 false BATT-S 0.615,0.698 2.448,0.896 1.833,0.198 10 false from Battery 2.458,0.583 2.615,0.781 0.156,0.198 10 false 1 2.698,0.719 3.01,0.917 0.313,0.198 10 false +B 3.729,0.719 4.188,0.917 0.458,0.198 10 false LIN 4.052,0.542 4.208,0.74 0.156,0.198 10 false 2 2.625,1.188 3.083,1.385 0.458,0.198 10 false A51 2.615,1.354 4.646,1.583 2.031,0.229 10 false Battery State Sensor Assembly 5.865,0.729 6.323,0.927 0.458,0.198 10 false LIN 5.51,0.542 5.969,0.74 0.458,0.198 10 false 135 6.042,1.823 6.656,2.021 0.615,0.198 10 false C54 6.042,2.021 6.5,2.219 0.458,0.198 10 false ECM 4.063,2 4.219,2.198 0.156,0.198 10 false 2 3.74,2.208 4.198,2.406 0.458,0.198 10 false LIN 2.625,2.688 3.24,2.885 0.615,0.198 10 false C57 2.625,2.865 5.375,3.063 2.75,0.198 10 false Generator Assembly 1.125,3.167 4.792,3.365 3.667,0.198 10 false : LIN Communication Line

PROCEDURE

1.CHECK CHARGING SYSTEM

OK

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the C54 ECM connector.


b.

Disconnect the C57 generator assembly connector.


c.

Disconnect the A51 battery state sensor assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C54-135 (LIN) - C57-2 (LIN) Always Below 1 Ω
C54-135 (LIN), C57-2 (LIN) or A51-2 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CLEAR DTCS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTCS
a.

Check for DTCs, and then write them down.

Powertrain > Engine > Trouble Codes
50001 372

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCS
4.CHECK FOR DTCS
a.

Allow the engine to idle for approximately 17 minutes or more.


b.

Check for DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only DTC P161A87 is output. A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C