81220
1.REMOVE FOG LIGHT ASSEMBLY LH
81210A
2.REMOVE FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.
88211B
3.REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
86790B
4.REMOVE FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
89341L
5.REMOVE FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89341K
6.REMOVE FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89347C
7.REMOVE FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89347B
8.REMOVE FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
85354
9.REMOVE HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)
85353
10.REMOVE HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
85208A
11.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A
12.REMOVE HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
85370A
13.REMOVE NO. 1 HEADLIGHT CLEANER WASHER HOSE ASSEMBLY (w/ Headlight Cleaner System)
Disengage the 10 clamps to remove the No. 1 headlight cleaner washer hose assembly.
82114
14.REMOVE NO. 4 ENGINE ROOM WIRE (w/o TOYOTA Parking Assist-sensor System)
w/ Pre-collision System:
Disengage the 9 clamps to remove the No. 4 engine room wire.
82114
15.REMOVE NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
Disengage each clamp to remove the No. 4 engine room wire.
| *A | w/ Panoramic View Monitor System | - | - |
16.REMOVE ULTRASONIC SENSOR CLIP
Remove each ultrasonic sensor clip.
| *A | w/ TOYOTA Parking Assist-sensor System | - | - |
52114A
17.REMOVE FRONT BUMPER EXTENSION MOUNTING BRACKET
Remove the 2 screws to remove the front bumper extension mounting bracket.
53395H
18.REMOVE HOOD TO RADIATOR GRILLE SEAL
Disconnect the hood to radiator grille seal as shown in the illustration.
Use the same procedure for the LH side and RH side.
Disengage the 16 clips to remove the hood to radiator grille seal.
53115B
19.REMOVE RADIATOR GRILLE BRACKET
Remove the 2 clips.
Remove the 2 clips and 10 screws.
|
Clip |
|
Screw |
Disengage the 4 claws and 3 guides.
Disengage the 6 guides to remove the radiator grille bracket.
52711
20.REMOVE FRONT BUMPER MOULDING
Remove the 2 screws.
Disengage the 8 clips and 3 guides to remove the front bumper moulding.
75311
21.REMOVE RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
Remove the 2 screws.
Disengage the 2 claws to remove the radiator grille (or front panel) emblem.
52526E
22.REMOVE NO. 1 FRONT BUMPER LOWER RETAINER
Remove the screw and No. 1 front bumper lower retainer.
53101
23.REMOVE RADIATOR GRILLE SUB-ASSEMBLY
Remove the 2 screws.
Disengage the 10 clips and 3 guides to remove the radiator grille sub-assembly.
81482C
24.REMOVE FOG LIGHT COVER LH
Disengage the 2 screws.
Disengage the 2 claws to remove the fog light cover LH.
81481E
25.REMOVE FOG LIGHT COVER RH
Use the same procedure as for the LH side.
52128B
26.REMOVE FRONT BUMPER HOLE COVER LH
| *a | Hook |
Disengage the 2 claws.
Disengage the hook to remove the front bumper hole cover LH.
52127D
27.REMOVE FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
53901B
28.REMOVE FRONT VALANCE PANEL SUB-ASSEMBLY (w/ Front Valance Panel)
Remove the 11 clips.
Disengage the 11 guides to remove the front valance panel sub-assembly.
52129B
29.REMOVE FRONT BUMPER LOWER COVER
Remove the 4 clips.
Disengage the 14 claws to remove the front bumper lower cover from the front bumper cover.
52611
30.REMOVE FRONT BUMPER ENERGY ABSORBER
Perform this procedure only when replacement of the front bumper energy absorber is necessary.
Disengage the 2 guides to remove the front bumper energy absorber.
52618
31.REMOVE FRONT BUMPER LOWER ABSORBER
Perform this procedure only when replacement of the front bumper lower absorber is necessary.
Disengage the 2 guides to remove the front bumper lower absorber.
52021
32.REMOVE FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Perform this procedure only when replacement of the front bumper reinforcement sub-assembly is necessary.
Disengage the 2 clamps.
Remove the 8 bolts and front bumper reinforcement sub-assembly.
52132A
33.REMOVE NO. 2 FRONT BUMPER REINFORCEMENT
Perform this procedure only when replacement of the No. 2 front bumper reinforcement is necessary.
Remove the 4 nuts and No. 2 front bumper reinforcement.
52146C
34.REMOVE FRONT BUMPER SIDE STAY LH
Perform this procedure only when replacement of the front bumper side stay LH is necessary.
Remove the bolt.
Disengage the 2 clips as shown in the illustration.
Disengage the claw to remove the front bumper side stay LH.
52145H
35.REMOVE FRONT BUMPER SIDE STAY RH
Use the same procedure as for the LH side.