52146C
1.INSTALL FRONT BUMPER SIDE STAY LH
Perform this procedure only when replacement of the front bumper side stay LH is necessary.
Engage the claw.
Engage the 2 clips as shown in the illustration.
Install the front bumper side stay LH with the bolt.
52145H
2.INSTALL FRONT BUMPER SIDE STAY RH
Use the same procedure as for the LH side.
52132A
3.INSTALL NO. 2 FRONT BUMPER REINFORCEMENT
Perform this procedure only when replacement of the No. 2 front bumper reinforcement is necessary.
Install the No. 2 front bumper reinforcement with the 4 nuts.
52021
4.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY
Perform this procedure only when replacement of the front bumper reinforcement sub-assembly is necessary.
Install the front bumper reinforcement sub-assembly with the 8 bolts.
Engage the 2 clamps.
52618
5.INSTALL FRONT BUMPER LOWER ABSORBER
Perform this procedure only when replacement of the front bumper lower absorber is necessary.
Engage the 2 guides to install the front bumper lower absorber.
52611
6.INSTALL FRONT BUMPER ENERGY ABSORBER
Perform this procedure only when replacement of the front bumper energy absorber is necessary.
Engage the 2 guides to install the front bumper energy absorber.
52129B
7.INSTALL FRONT BUMPER LOWER COVER
Engage the 14 claws.
Install the front bumper lower cover to front bumper cover with the 4 clips.
53901B
8.INSTALL FRONT VALANCE PANEL SUB-ASSEMBLY (w/ Front Valance Panel)
Engage the 11 guides.
Install the front valance panel sub-assembly with the 11 clips.
52128B
9.INSTALL FRONT BUMPER HOLE COVER LH
| *a | Hook |
Engage the hook.
Engage the 2 claws to install the front bumper hole cover LH.
52127D
10.INSTALL FRONT BUMPER HOLE COVER RH
Use the same procedure as for the LH side.
81482C
11.INSTALL FOG LIGHT COVER LH
Engage the 2 claws.
Install the fog light cover LH with the 2 screws.
81481E
12.INSTALL FOG LIGHT COVER RH
Use the same procedure as for the LH side.
53101
13.INSTALL RADIATOR GRILLE SUB-ASSEMBLY
Engage the 3 guides and 10 clips.
Install the radiator grille sub-assembly with the 2 screws.
52526E
14.INSTALL NO. 1 FRONT BUMPER LOWER RETAINER
Install the No. 1 front bumper lower retainer with the screw.
75311
15.INSTALL RADIATOR GRILLE (OR FRONT PANEL) EMBLEM
Engage the 2 claws.
Install the radiator grille (or front panel) emblem with the 2 screws.
52711
16.INSTALL FRONT BUMPER MOULDING
Engage the 3 guides and 8 clips.
Install the front bumper moulding with the 2 screws.
53115B
17.INSTALL RADIATOR GRILLE BRACKET
Engage the 6 guides.
Engage the 3 guides and 4 claws.
Install the 10 screws and 2 clips.
|
Screw |
|
Clip |
Install the radiator grille bracket with the 2 clips.
53395H
18.INSTALL HOOD TO RADIATOR GRILLE SEAL
Connect the hood to radiator grille seal as shown in the illustration.
Use the same procedure for the LH side and RH side.
Engage the 16 clips to install the hood to radiator grille seal.
52114A
19.INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET
Install the front bumper extension mounting bracket with the 2 screws.
20.INSTALL ULTRASONIC SENSOR CLIP
When installing the ultrasonic sensor clip, heat the front bumper cover using a heat light.
| Item | Temperature |
|---|---|
| Front Bumper Cover | 20 to 30 °C (68 to 86 °F) |
| *a | Heated Part |
| *b | Heat Light |
Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.
Do not heat the front bumper cover excessively.
Clean the front bumper cover surface.
Using a heat light, heat the front bumper cover surface.
Remove the double-sided tape from the front bumper cover.
Wipe off any tape adhesive residue with cleaner.
|
Primer |
Using a brush or felt, apply primer or equivalent to the ultrasonic sensor clip installation area.
Install a new ultrasonic sensor clip.
Using a heat light, heat the front bumper cover surface.
Remove the release paper from the ultrasonic sensor clip.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Install each ultrasonic sensor clip as shown in the illustration.
| *A | w/ TOYOTA Parking Assist-sensor System | - | - |
| *a | Line | - | - |
Install the ultrasonic sensor clip within the line on the front bumper cover.
Press the ultrasonic sensor clip firmly to install it.
82114
21.INSTALL NO. 4 ENGINE ROOM WIRE (w/o TOYOTA Parking Assist-sensor System)
w/ Pre-collision System:
Engage the 9 clamps to install the No. 4 engine room wire.
82114
22.INSTALL NO. 4 ENGINE ROOM WIRE (w/ TOYOTA Parking Assist-sensor System)
Engage each clamp to install the No. 4 engine room wire.
| *A | w/ Panoramic View Monitor System | - | - |
85370A
23.INSTALL NO. 1 HEADLIGHT CLEANER WASHER HOSE ASSEMBLY (w/ Headlight Cleaner System)
Engage the 10 clamps to install the No. 1 headlight cleaner washer hose assembly.
85208A
24.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY LH (w/ Headlight Cleaner System)
85207A
25.INSTALL HEADLIGHT WASHER ACTUATOR SUB-ASSEMBLY RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
85354
26.INSTALL HEADLIGHT WASHER COVER LH (w/ Headlight Cleaner System)
85353
27.INSTALL HEADLIGHT WASHER COVER RH (w/ Headlight Cleaner System)
Use the same procedure as for the LH side.
89347B
28.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89347C
29.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)
89341K
30.INSTALL FRONT CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
89341L
31.INSTALL FRONT CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)
86790B
32.INSTALL FRONT TELEVISION CAMERA ASSEMBLY (w/ Panoramic View Monitor System)
88211B
33.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-collision System)
81220
34.INSTALL FOG LIGHT ASSEMBLY LH
81210A
35.INSTALL FOG LIGHT ASSEMBLY RH
Use the same procedure as for the LH side.