Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Front)
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0417849 ULTRASONIC SENSOR(for Front) A

PARK ASSIST / MONITORING  ULTRASONIC SENSOR(for Front)  INSTALLATION  


PROCEDURE

Hide 89305 1.INSTALL ULTRASONIC SENSOR CUSHION SET

HINT:

Only perform this procedure when removing and installing the ultrasonic sensor cushion set.


a.

Install the ultrasonic sensor cushion set as shown in the illustration.

B549652C01
0,0 0,0 false
V113147

Install in this Direction - -



Hide 89347B 2.INSTALL FRONT CORNER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front corner ultrasonic sensor retainer is necessary.

·

If a front corner ultrasonic sensor retainer has been removed, replace it with a new one.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.

Clean the surface of the front bumper assembly.

i.

Remove any remaining double-sided tape from the front bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



b.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 25 mm (0.984 in.)


Cover the sensor installation hole with a 25 mm (0.984 in.) circular piece of tape.


c.
E432232C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the front corner ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.




d.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


e.

Peel off the release paper from a new front corner ultrasonic sensor retainer.


f.
E432233C01
1.406,1.854 1.406,1.51 false 1.333,1.854 1.542,2.063 0.208,0.208 10 true *a
*a Scribed Line
V100155

Press Here


Align the front corner ultrasonic sensor retainer with the mark on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the front corner ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a front corner ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front corner ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front corner ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front corner ultrasonic sensor retainer and front bumper assembly.



Hide 89347C 3.INSTALL FRONT CENTER ULTRASONIC SENSOR RETAINER

HINT:
·

Perform this procedure only when replacement of the front center ultrasonic sensor retainer is necessary.

·

If a front center ultrasonic sensor retainer has been removed, replace it with a new one. Install the front center ultrasonic sensor with a new front center ultrasonic sensor retainer as a set to the front bumper assembly.

·

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.



a.
E397279

Engage the 2 claws to install a new front center ultrasonic sensor retainer to the front center ultrasonic sensor.


b.

Clean the surface of the front bumper assembly.

i.

Remove any remaining double-sided tape from the front bumper assembly.


ii.

Wipe off any adhesive residue with cleaner.



c.
E335575C01
1.719,1.125 1.938,1.292 0.219,0.167 10 true *a
*a 19 mm (0.748 in.)


Cover the sensor installation hole with a 19 mm (0.748 in.) circular piece of tape.


d.
E432226C01
0,0 0,0 false
V100144

Primer


Using a brush or felt, apply primer or equivalent to the front center ultrasonic sensor retainer installation area.

NOTICE:
·

Use a clean brush or felt.

·

Do not touch the front bumper assembly until the primer has dried.




e.

Confirm that the primer has completely dried by touching the front bumper assembly. Then remove the tape.


f.

Peel off the release paper from the front center ultrasonic sensor retainer.


g.
E432227C01
1.885,1.688 1.885,1.333 true 1.802,1.698 2.01,1.896 0.208,0.198 10 true *a
*a Scribed Line
V100155

Press Here


Align the front center ultrasonic sensor retainer with front center ultrasonic sensor with the mark on the front bumper assembly and install it as shown in the illustration.

NOTICE:
·

Ensure that the sensor tip is correctly inserted into the sensor installation hole of the front bumper assembly.

·

Ensure that the front center ultrasonic sensor retainer is within the scribed line.

·

The double-sided tape of a front center ultrasonic sensor retainer will deteriorate if it is detached. Make sure to replace the front center ultrasonic sensor retainer with a new one when reattachment is necessary.



HINT:

Press the area shown in the illustration with a force of 30 N (3.0 kgf) for 3 seconds to securely install the front center ultrasonic sensor retainer to the front bumper assembly. Confirm there is no clearance between the front center ultrasonic sensor retainer and front bumper assembly.



Hide 89341K 4.INSTALL FRONT CORNER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.
E432230C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the front corner ultrasonic sensor as shown in the illustration.


b.

Connect the connector.


Hide 89341L 5.INSTALL FRONT CENTER ULTRASONIC SENSOR

HINT:

The illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.


a.

When replacing only the front center ultrasonic sensor:

i.
E432224C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws to install the front center ultrasonic sensor as shown in the illustration.



b.

Connect the connector.


Hide 6.INSTALL FRONT BUMPER ASSEMBLY

Hide 8.PERFORM CALIBRATION (w/ Parking Support Brake System)