Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER › from 2020.11
RM37A0E _59 Vehicle Exterior _086903 EXTERIOR PANELS / TRIM _0417657 REAR BUMPER A

EXTERIOR PANELS / TRIM  REAR BUMPER  REASSEMBLY  


PROCEDURE

Hide 52171C 1.INSTALL REAR BUMPER REINFORCEMENT

HINT:

Perform this procedure only when replacement of the rear bumper reinforcement is necessary.


a.
B565955

Install the rear bumper reinforcement with the 6 nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 52592 2.INSTALL REAR BUMPER SIDE SEAL LH

HINT:

Perform this procedure only when replacement of the rear bumper side seal LH is necessary.


a.
B565954C01
0,0 0,0 false
V100135

Nut
V100136

Clip


Install the nut and clip.


b.
B565953C01
0,0 0,0 false
V100135

Screw
V100136

Clip


Install the rear bumper side seal LH with the screw and clip.


Hide 52591 3.INSTALL REAR BUMPER SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 52156A 4.INSTALL REAR BUMPER SIDE SUPPORT LH

HINT:

Perform this procedure only when replacement of the rear bumper side support LH is necessary.


a.
B567682

Engage the 2 claws.


b.
B565952

Engage the 3 clips as shown in the illustration to install the rear bumper side support LH.


Hide 52155A 5.INSTALL REAR BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure as for the LH side.


Hide 52563D 6.INSTALL REAR BUMPER UPPER RETAINER LH

a.
B565957

Engage the 2 guides to install the rear bumper upper retainer LH to the rear combination light assembly LH.


Hide 52562E 7.INSTALL REAR BUMPER UPPER RETAINER RH

HINT:

Use the same procedure as for the LH side.


Hide 81560 8.INSTALL REAR COMBINATION LIGHT ASSEMBLY LH

a.
B565958

Connect the 3 connectors.


b.

Engage the 3 clamps.


c.
B565959C01
0.99,1.333 1.104,0.771 true 1.708,1.938 1.865,1.083 true 0.896,1.333 1.104,1.5 0.208,0.167 10 true *a 1.625,1.938 1.833,2.104 0.208,0.167 10 true *b
*a Guide
*b Pin


Engage the guide and pin.


d.

Install the rear combination light assembly LH with the 3 screws.


Hide 81550 9.INSTALL REAR COMBINATION LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 52463 10.INSTALL REAR BUMPER PAD LH

HINT:

When installing the rear bumper pad LH, heat the rear bumper cover using a heat light.


Heating Temperature:
Item Temperature
Rear Bumper Cover 20 to 30 °C (68 to 86 °F)


CAUTION:
E306500C23
2.365,2 2.698,2 false 0.5,2.333 0.5,2.667 true 0.427,2.708 0.74,2.865 0.313,0.156 10 false *a 2.76,1.927 3.073,2.083 0.313,0.156 10 false *b
*a Heated Part
*b Heat Light


·

Do not touch the heat light and heated parts, touching the heat light may result in burns.

·

Touching heated parts for a long time may result in burns.



NOTICE:

Do not heat the rear bumper cover excessively.


a.

Clean the rear bumper cover surface.

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove any double-sided tape from the rear bumper cover.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear bumper pad LH.

i.

Using a heat light, heat the rear bumper cover surface.


ii.

Remove the release paper from the rear bumper pad LH.

HINT:

After removing the release paper, keep the exposed adhesive free from foreign matter.



iii.
B565950C01
1.823,0.865 2.802,0.813 2.802,0.813 1.854,0.74 true 2.844,0.708 3.052,0.896 0.208,0.188 10 true *a
*a Line


Install the rear bumper pad LH as shown in the illustration.

HINT:
·

Install the rear bumper pad LH along the line on the rear bumper cover.

·

Press the rear bumper pad LH firmly to install it.

·

Use the same procedure for the RH side and LH side.





Hide 52615 11.INSTALL REAR BUMPER ENERGY ABSORBER

a.

Engage the 7 claws to install the rear bumper energy absorber.

B565948


Hide 52169C 12.INSTALL REAR BUMPER LOWER COVER

a.

Engage the 2 guides and 14 claws.

B565947


b.

Install the rear bumper lower cover to the rear bumper cover with the 2 screws and 4 clips.

B565946C01
0,0 0,0 false
V100135

Screw
V100136

Clip



Hide 52151G 13.INSTALL REAR BUMPER EXTENSION

a.

Engage the 6 guides and 10 claws.

B565945


b.

Install the 6 clips.

B565944


c.

Install the rear bumper extension with each clip.

B565943C02
2.552,1.146 2.792,1.354 0.24,0.208 12 true *A 4.406,1.177 4.646,1.385 0.24,0.208 12 true *A
*A w/o Kick Sensor - -



Hide 81490C 14.INSTALL REAR FOG LIGHT ASSEMBLY LH

Hide 81480A 15.INSTALL REAR FOG LIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 82183 16.INSTALL NO. 3 LUGGAGE ROOM WIRE

a.

Engage each clamp to install the No. 3 luggage room wire.

B604741C02
5.125,1.615 6.188,2.354 1.063,0.74 5.146,1.625 5.365,1.823 0.219,0.198 12 true *A
*A w/ Kick Sensor - -



Hide 17.INSTALL KICK DOOR CONTROL SENSOR WITH BRACKET (w/ Kick Sensor)

Hide 89348R 18.INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89348S 19.INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

Hide 89342 20.INSTALL REAR CORNER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

Hide 89342A 21.INSTALL REAR CENTER ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)