Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0453179 TOYOTA MULTI OPERATION TOUCH SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  B15D6  Display Disconnected (Multi Display)  


DESCRIPTION

The multi-display assembly and integration control sub-assembly are connected by AVC-LAN communication lines.

This DTC is stored when an AVC-LAN communication error occurs between the multi-display assembly and integration control sub-assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D6 Display Disconnected A device that is listed in the AVC-LAN connected device record of the integration control sub-assembly is missing
·

Multi-display assembly power source circuit

·

AVC-LAN circuit between integration control sub-assembly and multi-display assembly

·

Multi-display assembly

·

Integration control sub-assembly

·

Harness or connector



WIRING DIAGRAM

E444860E08
4.177,0.802 5.177,1.021 1,0.219 10 false RADIO NO. 2 2.24,0.604 3.99,0.823 1.75,0.219 10 false from Auxiliary Battery 2.573,1.542 3.844,1.75 1.271,0.208 10 false from ACC Relay 3.625,2.448 3.885,2.688 0.26,0.24 10 false 18 3.292,2.563 3.75,2.781 0.458,0.219 10 false TX+ 3.635,2.844 3.958,3.063 0.323,0.219 10 false 40 5.406,2.438 5.5,2.594 0.094,0.156 10 false 7 5.333,2.833 5.51,2.99 0.177,0.156 10 false 19 3.302,2.958 3.75,3.198 0.448,0.24 10 false TX- 5.615,2.594 6.021,2.833 0.406,0.24 10 false TX+ 5.333,3.25 5.521,3.406 0.188,0.156 10 false 13 5.604,3.365 6.01,3.521 0.406,0.156 10 false GND1 5.344,1.417 5.521,1.573 0.177,0.156 10 false 24 5.615,1.583 5.927,1.74 0.313,0.156 10 false ACC 5.344,0.531 5.521,0.688 0.177,0.156 10 false 12 5.615,0.656 5.74,0.813 0.125,0.156 10 false B 5.615,3 5.99,3.177 0.375,0.177 10 false TX- 2.396,3.375 2.927,3.563 0.531,0.188 10 false H8 2.406,3.552 3.573,3.99 1.167,0.438 10 false Integration Control Sub-assembly 5.292,4 6.771,4.198 1.479,0.198 10 false Multi-display Assembly 5.281,3.823 5.708,3.99 0.427,0.167 10 false H7 1.146,4.135 3.167,4.292 2.021,0.156 10 false : AVC-LAN Communication Line 4.281,1.719 5.125,1.896 0.844,0.177 10 false ECU-ACC

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the integration control sub-assembly, always replace it with a new one. If a integration control sub-assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The integration control sub-assembly may not operate normally.



·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check for optional components.

i.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.






A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY POWER SOURCE)
a.

Disconnect the H7 multi-display assembly connector.


b.
E206146C58
1.49,0.323 1.906,0.573 0.417,0.25 0.594,1.927 0.698,1.927 0.698,1.927 0.885,1.531 true 2.896,2.01 2.823,2.01 2.823,2.01 2.479,1.542 true 2.938,0.771 2.865,0.771 2.865,0.771 2.5,1.26 true 0.104,0.073 0.417,0.229 0.313,0.156 10 false *a 1.573,0.375 1.885,0.531 0.313,0.156 10 false H7 0.219,1.854 0.635,2.042 0.417,0.188 10 false GND1 2.958,1.948 3.333,2.177 0.375,0.229 10 false ACC 3,0.708 3.375,0.938 0.375,0.229 10 false B
*a Front view of wire harness connector
(to Multi-display Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H7-13 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H7-12 (B) - H7-13 (GND1) Ignition switch off 11 to 14 V
H7-24 (ACC) - H7-13 (GND1) Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (INTEGRATION CONTROL SUB-ASSEMBLY - MULTI-DISPLAY ASSEMBLY)
a.

Disconnect the H8 integration control sub-assembly connector.


b.

Disconnect the H7 multi-display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-18 (TX+) - H7-7 (TX+) Always Below 1 Ω
H8-40 (TX-) - H7-19 (TX-) Always Below 1 Ω
H8-18 (TX+) or H7-7 (TX+) - Body ground Always 10 kΩ or higher
H8-40 (TX-) or H7-19 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE MULTI-DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE MULTI-DISPLAY ASSEMBLY
a.

Replace the multi-display assembly with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY>REMOVAL


b.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG