Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › TOYOTA MULTI OPERATION TOUCH SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0453179 TOYOTA MULTI OPERATION TOUCH SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  TOYOTA MULTI OPERATION TOUCH SYSTEM  B1522  Lost Communication with DCU Video Line Signal  


DESCRIPTION

The radio receiver assembly and integration control sub-assembly are connected via video signal (digital) lines.

This DTC is stored when a video signal (digital) line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1522 Lost Communication with DCU Video Line Signal GVIF disconnected (from radio receiver assembly to integration control sub-assembly)
·

Harness or connector (GVIF cable)

·

Integration control sub-assembly

·

Radio receiver assembly



WIRING DIAGRAM

E381479E97
1.208,3.125 2.646,3.448 1.438,0.323 10 false : GVIF Cable 1.271,2.333 1.771,2.552 0.5,0.219 10 false b2 1.271,2.51 2.417,2.917 1.146,0.406 10 false Integration Control Sub-assembly 2.177,0.823 2.677,1.042 0.5,0.219 10 false GV+ 2.135,1.969 2.635,2.188 0.5,0.219 10 false GVG 4.854,2.333 5.354,2.552 0.5,0.219 10 false b1 4.865,2.5 6.542,2.74 1.677,0.24 10 false Radio Receiver Assembly 4.875,1.229 5.375,1.448 0.5,0.219 10 false 2 4.875,0.667 5.375,0.885 0.5,0.219 10 false 1 4.865,1.865 5.365,2.083 0.5,0.219 10 false 3 2.188,1.365 2.688,1.583 0.5,0.219 10 false GV- 5.063,1.969 5.563,2.188 0.5,0.219 10 false GVG 2.552,0.688 3.052,0.906 0.5,0.219 10 false 1 2.552,1.24 3.052,1.458 0.5,0.219 10 false 2 2.583,1.833 3.083,2.052 0.5,0.219 10 false 3 5.042,0.823 5.542,1.042 0.5,0.219 10 false GV+ 5.052,1.375 5.552,1.594 0.5,0.219 10 false GV- 3.719,1.813 4.219,2.031 0.5,0.219 10 false * 2.385,3.135 3.823,3.458 1.438,0.323 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:

When replacing the integration control sub-assembly, always replace it with a new one. If a integration control sub-assembly which was installed to another vehicle is used, the following may occur:

·

A communication malfunction DTC may be stored.

·

The integration control sub-assembly may not operate normally.



PROCEDURE

1.CHECK DTC
a.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY - INTEGRATION CONTROL SUB-ASSEMBLY)
a.
E435809C10
1.5,0.667 1.917,0.917 0.417,0.25 1.5,2.917 1.917,3.167 0.417,0.25 1.771,1.5 2.188,1.146 2.188,1.146 2.344,1.146 true 1.771,3.635 2.188,3.281 2.188,3.281 2.344,3.281 true 1.063,3.302 1.219,3.302 1.219,3.302 1.635,3.625 true 1.042,1.177 1.198,1.177 1.198,1.177 1.615,1.5 true 1.74,1.656 1.99,2.125 1.99,2.125 2.146,2.125 true 1.729,3.771 1.979,4.24 1.979,4.24 2.135,4.24 true 0.792,0.635 1.104,0.833 0.313,0.198 10 false *a 0.813,2.885 1.125,3.083 0.313,0.198 10 false *b 1.604,0.708 2.219,0.906 0.615,0.198 10 false b2 1.615,2.969 2.229,3.167 0.615,0.198 10 false b1 0.719,1.104 1.135,1.302 0.417,0.198 10 false GV+ 2.427,3.198 3.198,3.396 0.771,0.198 10 false GV- 2.417,1.073 2.813,1.292 0.396,0.219 10 false GV- 0.75,3.219 1.521,3.417 0.771,0.198 10 false GV+ 2.198,2.052 2.969,2.25 0.771,0.198 10 false GVG 2.188,4.156 2.958,4.354 0.771,0.198 10 false GVG
*a Front view of wire harness connector
(to Integration Control Sub-assembly)
*b Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the b2 integration control sub-assembly connector.


b.

Disconnect the b1 radio receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
b2-1 (GV+) - b1-1 (GV+) Always Below 1 Ω
b2-2 (GV-) - b1-2 (GV-) Always Below 1 Ω
b2-3 (GVG) - b1-3 (GVG) Always Below 1 Ω
b2-1 (GV+) or b1-1 (GV+) - Body ground Always 10 kΩ or higher
b2-2 (GV-) or b1-2 (GV-) - Body ground Always 10 kΩ or higher
b2-3 (GVG) or b1-3 (GVG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK INTEGRATION CONTROL SUB-ASSEMBLY
a.

Replace the integration control sub-assembly with a new one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>MULTI-DISPLAY ECU>REMOVAL


b.

Clear the DTCs.

Body Electrical > D-SEAT SW > Clear DTCs
50002 181

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > D-SEAT SW > Trouble Codes
50001 181
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (INTEGRATION CONTROL SUB-ASSEMBLY IS DEFECTIVE)

NG

REPLACE RADIO RECEIVER ASSEMBLY