This DTC is stored when the telematics transceiver detects an open or short in the manual (SOS) switch indicator (green) circuit of the manual (SOS) switch.
The manual (SOS) switch indicator (green) illuminates after the ignition switch is turned to ON.
If the telematics system is not active, the manual (SOS) switch indicator (green) will turn off.
If the telematics system is active, the manual (SOS) switch indicator (green) will blink while communicating with the call center.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157111 | Indicator (Green) Circuit Short to Ground | Manual (SOS) switch indicator (green) impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual (SOS) switch) ·
Harness or connector |
| B157113 | Indicator (Green) Circuit Open | Manual (SOS) switch indicator (green) impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON | ·
Telematics transceiver ·
Map light assembly (manual (SOS) switch) ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component without harness connected
(Map Light Assembly (Manual (SOS) Switch)) |
Remove the map light assembly (manual (SOS) switch).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect 2 dry-cell batteries (1.5 V each) in series.
Connect a positive (+) lead from batteries to terminal 6 (IND2) and a negative (-) lead to terminal 1 (GND3) of the map light assembly (manual (SOS) switch) connector.
Check if the manual (SOS) switch green indicator comes on.
Manual (SOS) switch green indicator illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H11 telematics transceiver connector.
Disconnect the R11 map light assembly (manual (SOS) switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H11-22 (IND2) - R11-6 (IND2) | Always | Below 1 Ω |
| H11-22 (IND2) or R11-6 (IND2) - Body ground | Always | 10 kΩ or higher |
| H11-3 (SIG-) - R11-1 (GND3) | Always | Below 1 Ω |
| H11-3 (SIG-) or R11-1 (GND3) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT