Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086879 TELEMATICS _0453411 TELEMATICS SYSTEM(for eCall) J

TELEMATICS  TELEMATICS SYSTEM(for eCall)  Emergency Call Switch Illumination Circuit  


WIRING DIAGRAM

E458951E01
2.427,2.26 2.896,2.427 0.469,0.167 10 false H11 2.427,2.427 4.094,2.823 1.667,0.396 10 false Telematics Transceiver 4.292,2.625 4.667,2.833 0.375,0.208 10 false R11 4.292,2.813 7.115,3.156 2.823,0.344 10 false Map Light Assembly (Manual (SOS) Switch) 4.26,0.896 4.521,1.115 0.26,0.219 10 false 8 4.26,1.698 4.573,1.938 0.313,0.24 10 false 1 4.458,0.906 4.844,1.083 0.385,0.177 10 false RRID 1.104,1.031 2.656,1.313 1.552,0.281 10 false from IG2-NO.2 Relay 4.458,1.719 4.927,1.896 0.469,0.177 10 false GND3 4.969,2.135 6.417,2.313 1.448,0.177 10 false Manual (SOS) Switch 2.823,1.198 3.938,1.396 1.115,0.198 10 false ECU-IG2 NO.3 3.292,1.823 3.76,2 0.469,0.177 10 false SIG- 3.708,1.708 4.021,1.948 0.313,0.24 10 false 3

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the telematics transceiver, make sure to replace it with a new one.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



HINT:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH))
a.

Disconnect the H11 telematics transceiver connector.


b.

Disconnect the R11 map light assembly (manual (SOS) switch) connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R11-8 (RRID) - Body Ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H11-3 (SIG-) - R11-1 (GND3) Always Below 1 Ω
H11-3 (SIG-) or R11-1 (GND3) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)
a.
E430891C03
0.875,1.115 0.771,0.74 false 2.885,1.135 2.99,0.76 false 0.073,0.094 0.354,0.333 0.281,0.24 10 false *a 2.76,0.552 3.188,0.771 0.427,0.219 10 false GND3 0.51,0.531 0.938,0.75 0.427,0.219 10 false RRID
*a Component without harness connected
(Map Light Assembly (Manual (SOS) Switch))


Remove the map light assembly (manual (SOS) switch).

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Apply auxiliary battery voltage to the connector.

Measurement Condition Condition Specified Condition
Auxiliary battery positive (+) → 8 (RRID)
Auxiliary battery negative (-) → 1 (GND3)
Always Manual (SOS) switch illumination comes on


c.

Check if the manual (SOS) switch illumination comes on.

OK:

The manual (SOS) switch illumination comes on.



Result:
Proceed to
OK
NG



OK

3.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE MAP LIGHT ASSEMBLY (MANUAL (SOS) SWITCH)

3.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT