Home › Audio / Visual / Telematics › TELEMATICS › TELEMATICS SYSTEM (for eCall) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086879 TELEMATICS _0453411 TELEMATICS SYSTEM(for eCall) C

TELEMATICS  TELEMATICS SYSTEM(for eCall)  B15CB11  Telephone Main Antenna Circuit Short to Ground  B15CB13  Telephone Main Antenna Circuit Open  


DESCRIPTION

If an open or short circuit in the roof antenna assembly is detected as a result of a terminal check performed by the telematics transceiver, these DTCs will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15CB11 Telephone Main Antenna Circuit Short to Ground Telephone antenna assembly impedance (Ω) is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Short circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly


B15CB13 Telephone Main Antenna Circuit Open Telephone antenna assembly impedance (Ω) is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON (Open circuit)
·

Telematics transceiver

·

Roof antenna assembly

·

Antenna cord sub-assembly

·

No. 3 antenna cord sub-assembly

·

No. 4 antenna cord sub-assembly



WIRING DIAGRAM

E429874E46
0.292,1.219 1.906,1.552 1.615,0.333 10 false Roof Antenna Assembly 0.281,1.052 0.438,1.25 0.156,0.198 10 false E 1.135,0.438 1.292,0.635 0.156,0.198 10 false 4 2.49,0.365 2.646,0.563 0.156,0.198 10 false 6 4.375,0.365 4.531,0.563 0.156,0.198 10 false 6 4.76,0.365 4.917,0.563 0.156,0.198 10 false 6 1.625,0.688 1.833,0.875 0.208,0.188 10 false *3 3.583,0.688 3.792,0.875 0.208,0.188 10 false *2 5.427,0.688 5.635,0.875 0.208,0.188 10 false *1 5.927,0.458 6.135,0.646 0.208,0.188 10 false 1 2.49,0.563 2.646,0.76 0.156,0.198 10 false I 2.896,0.563 3.052,0.76 0.156,0.198 10 false H 4.76,0.563 4.938,0.75 0.177,0.188 10 false F 4.365,0.563 4.521,0.76 0.156,0.198 10 false G 6.125,0.563 6.479,0.76 0.354,0.198 10 false TEL 6.094,1.042 6.281,1.229 0.188,0.188 10 false C 6.083,1.208 6.792,1.625 0.708,0.417 10 false Telematics Transceiver 1.573,2.229 4.427,2.458 2.854,0.229 10 false *1: Antenna Cord Sub-assembly 1.573,2.667 4.031,2.875 2.458,0.208 10 false *2: No. 3 Antenna Cord Sub-assembly 1.583,3.094 4.042,3.302 2.458,0.208 10 false *3: No. 4 Antenna Cord Sub-assembly 2.896,0.365 3.052,0.563 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for eCall)>PRECAUTION

·

When replacing the telematics transceiver, make sure to replace it with a new one.



PROCEDURE

1.CHECK DTC
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON and wait for 10 seconds or more.


d.

Turn the GTS on.


e.

Clear the DTCs.

Body Electrical > Telematics > Clear DTCs
50002 459

f.

Check for DTCs and check that no DTCs are output.

Body Electrical > Telematics > Trouble Codes
50001 459
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT ROOF ANTENNA ASSEMBLY
2.INSPECT ROOF ANTENNA ASSEMBLY
a.

Remove the roof antenna assembly.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEPHONE ANTENNA>REMOVAL


b.
E271865C14
1.969,1.479 2.229,1.729 false 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 2.26,1.708 2.573,1.906 0.313,0.198 10 false 4a
*a Component without harness connected
(Roof Antenna Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 - 4a Always 9 to 11 kΩ



Result:
Proceed to
OK
NG



OK

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE ROOF ANTENNA ASSEMBLY

3.INSPECT NO. 4 ANTENNA CORD SUB-ASSEMBLY
a.
E457870C01
0.99,0.781 1.344,1.01 0.354,0.229 1.198,1.333 1.552,1.115 false 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 1.104,0.802 1.417,1 0.313,0.198 10 false E 1.021,1.302 1.333,1.5 0.313,0.198 10 false 4a
*a Component without harness connected
(No. 4 Antenna Cord Sub-assembly)


Disconnect the E No. 4 antenna cord sub-assembly connector.


b.
E432126C24
1.604,0.198 2.021,0.448 0.417,0.25 0.833,1.594 1.021,1.208 false 0.292,0.24 0.604,0.438 0.313,0.198 10 false *a 1.771,0.229 2.031,0.5 0.26,0.271 10 false I 0.719,1.583 1.01,1.865 0.292,0.281 10 false 6a
*a Component without harness connected
(No. 4 Antenna Cord Sub-assembly)


Disconnect the I No. 4 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-4 - I-6 Always Below 1 Ω
E-4a - I-6a Always Below 1 Ω
E-4 or I-6 - Body ground Always 10 kΩ or higher
E-4a or I-6a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 4 ANTENNA CORD SUB-ASSEMBLY

4.INSPECT NO. 3 ANTENNA CORD SUB-ASSEMBLY
a.
E356779C83
1.552,0.438 1.906,0.667 0.354,0.229 2.635,1.615 2.51,1.219 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a 1.677,0.458 1.99,0.656 0.313,0.198 10 false H 2.573,1.635 2.885,1.833 0.313,0.198 10 false 6a
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


Disconnect the H No. 3 antenna cord sub-assembly connector.


b.
E437617C15
1.583,0.333 2,0.583 0.417,0.25 0.917,1.552 1.042,1.167 false 0.135,0.146 0.448,0.302 0.313,0.156 10 false *a 0.813,1.552 1.125,1.75 0.313,0.198 10 false 6a 1.74,0.354 2.052,0.552 0.313,0.198 10 false G
*a Component without harness connected
(No. 3 Antenna Cord Sub-assembly)


Disconnect the G No. 3 antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H-6 - G-6 Always Below 1 Ω
H-6a - G-6a Always Below 1 Ω
H-6 or G-6 - Body ground Always 10 kΩ or higher
H-6a or G-6a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE NO. 3 ANTENNA CORD SUB-ASSEMBLY

5.INSPECT ANTENNA CORD SUB-ASSEMBLY
a.
E356779C84
1.552,0.438 1.906,0.667 0.354,0.229 2.635,1.615 2.51,1.219 true 0.208,0.135 0.521,0.333 0.313,0.198 10 false *a 1.677,0.458 1.99,0.656 0.313,0.198 10 false F 2.573,1.635 2.885,1.833 0.313,0.198 10 false 6a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the F antenna cord sub-assembly connector.


b.
E418545C16
1.563,0.24 1.979,0.49 0.417,0.25 2.24,1.875 1.906,1.521 false 1.74,0.313 1.896,0.51 0.156,0.198 10 false C 2.271,1.885 2.604,2.083 0.333,0.198 10 false 1a 0.167,0.146 0.365,0.323 0.198,0.177 10 false *a
*a Component without harness connected
(Antenna Cord Sub-assembly)


Disconnect the C antenna cord sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F-6 - C-1 Always Below 1 Ω
F-6a - C-1a Always Below 1 Ω
F-6 or C-1 - Body ground Always 10 kΩ or higher
F-6a or C-1a - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEMATICS TRANSCEIVER

NG

REPLACE ANTENNA CORD SUB-ASSEMBLY

6.REPLACE TELEMATICS TRANSCEIVER
a.

Replace the telematics transceiver with a new one.

Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL


Result:
Proceed to
NEXT



NEXT