Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0418857 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


E432301N03
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 5.292,6.198 5.729,6.448 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 3.469,7.698 3.781,7.896 0.313,0.198 10 false MB 4.292,0.24 4.604,0.438 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false H42 2.052,1.479 2.365,1.677 0.313,0.198 10 false H43 2.052,1.802 2.365,2 0.313,0.198 10 false H44 0.875,1.083 1.188,1.281 0.313,0.198 10 false 4D 0.875,1.667 1.188,1.865 0.313,0.198 10 false 4C 0.865,2.031 1.177,2.229 0.313,0.198 10 false 4E 0.906,2.25 1.219,2.448 0.313,0.198 10 false 4F 5.844,1.146 6.156,1.344 0.313,0.198 10 false 4B 5.833,1.76 6.146,1.958 0.313,0.198 10 false 4A 1.229,3.292 1.542,3.49 0.313,0.198 10 false H44 3.26,3.271 3.573,3.469 0.313,0.198 10 false H43 5.552,3.26 5.865,3.458 0.313,0.198 10 false H42 1.823,4.615 2.135,4.813 0.313,0.198 10 false 4A 1.229,6.208 1.542,6.406 0.313,0.198 10 false 4C 3.802,6.167 4.115,6.365 0.313,0.198 10 false 4D 6.438,6.24 6.75,6.438 0.313,0.198 10 false 4E 5.427,6.24 5.74,6.438 0.313,0.198 10 false 4F 5.51,4.615 5.823,4.813 0.313,0.198 10 false 4B

a.

Disconnect the MB main body ECU (multiplex network body ECU) connector.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground Ground Always Below 1 Ω
MB-31 (BECU) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
MB-30 (ACC) - Body ground ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-32 (IG) - Body ground IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the MB main body ECU (multiplex network body ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
4D-25 - Body ground LIN communication line Ignition switch ON Pulse generation
4B-17 - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B131578N62
3.385,0.229 3.802,0.479 0.417,0.25 3.458,0.271 3.823,0.5 0.365,0.229 10 false J18

a.

Disconnect the J18 multiplex network master switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
J18-11 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J18-12 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the J18 multiplex network master switch assembly connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
J18-17 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation
J18-16 (LIN2) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)


B286202C51
2.031,0.583 2.448,0.833 0.417,0.25 2.031,0.885 2.448,1.135 0.417,0.25 2.135,0.615 2.458,0.823 0.323,0.208 10 false J24 2.51,0.604 2.833,0.813 0.323,0.208 12 false *A 2.51,0.906 2.833,1.115 0.323,0.208 12 false *B 2.167,0.927 2.49,1.135 0.323,0.208 10 false J8
*A for LHD *B for RHD


a.

Disconnect the J24*1 or J8*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J24-1 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J8-1 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the J24*1 or J8*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)


B286202C50
2.031,0.583 2.448,0.833 0.417,0.25 2.031,0.885 2.448,1.135 0.417,0.25 2.167,0.625 2.49,0.833 0.323,0.208 10 false J8 2.51,0.615 2.833,0.823 0.323,0.208 12 false *A 2.51,0.917 2.833,1.125 0.323,0.208 12 false *B 2.146,0.917 2.469,1.125 0.323,0.208 10 false J24
*A for LHD *B for RHD


a.

Disconnect the J8*1 or J24*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J8-1 (GND) - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
J24-1 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the J8*1 or J24*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J8-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Terminal Description Condition Specified Condition
J24-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)


B203471N84
2.167,0.698 2.583,0.948 0.417,0.25 2.292,0.74 2.625,0.927 0.333,0.188 10 false K4

a.

Disconnect the K4 power window regulator motor assembly (rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K4-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
K4-1 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the K4 power window regulator motor assembly (rear RH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K4-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)


B203471N85
2.167,0.75 2.583,1 0.417,0.25 2.281,0.802 2.563,0.99 0.281,0.188 10 false K9

a.

Disconnect the K9 power window regulator motor assembly (rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
K9-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
K9-1 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the K9 power window regulator motor assembly (rear LH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
K9-9 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Sliding Roof System)


B417851N81
3.333,0.083 3.75,0.333 0.417,0.25 3.469,0.115 3.781,0.313 0.313,0.198 10 false R2

a.

Disconnect the R2 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R2-1 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
R2-2 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the R2 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R2-7 (MPX1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Panoramic Moon Roof System)


B567062N01
3.365,0.208 3.781,0.458 0.417,0.25 3.458,0.25 4.219,0.813 0.76,0.563 10 false R19

a.

Disconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R19-8 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
R19-12 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the R19 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R19-11 (MPX1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Panoramic Moon Roof System)


B567062N02
3.375,0.146 3.792,0.396 0.417,0.25 3.458,0.188 4.073,0.583 0.615,0.396 10 false R20

a.

Disconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
R20-8 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
R20-12 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the R20 roof sunshade ECU (sliding roof drive gear assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
R20-11 (MPX1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B506743C07
2.021,0.375 2.5,0.625 0.479,0.25 4.542,0.375 5.021,0.625 0.479,0.25 3.156,0.375 3.635,0.625 0.479,0.25 4.688,0.417 5,0.615 0.313,0.198 10 false H48 3.333,0.417 3.646,0.615 0.313,0.198 10 false M5 2.167,0.417 2.583,0.625 0.417,0.208 10 false A19 2.563,0.417 2.979,0.625 0.417,0.208 12 false *A
*A for Gasoline Model - -


a.

Disconnect the H48 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-4 (+B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H48-18 (E) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H48 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H48-13 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY)


B439652N16
3.417,0.313 3.833,0.563 0.417,0.25 3.51,0.365 3.823,0.563 0.313,0.198 10 false H52

a.

Disconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H52-7 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H52-1 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H52 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H52-5 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID Code Box)


B463193N31
3.344,0.146 3.792,0.417 0.448,0.271 3.448,0.198 4.063,0.396 0.615,0.198 10 false H53

a.

Disconnect the H53 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Terminal Description Condition Specified Condition
H53-1 (+B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
H53-5 (GND) - Body ground Ground Ignition switch off Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the H53 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
H53-2 (LIN1) - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)


B538704N07
3.333,0.083 3.76,0.313 0.427,0.229 3.458,0.104 3.771,0.302 0.313,0.198 10 false V7

a.

Disconnect the V7 kick door control sensor connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
V7-2 (B) - Body ground Auxiliary battery power supply Ignition switch off*1
Always*2
11 to 14 V
V7-7 (GND) - Body ground Ground Always Below 1 Ω

*1: for HV Model

*2: for Gasoline Model



c.

Reconnect the V7 kick door control sensor connector.


d.

Measure the pulse according to the value(s) in the table below.

Terminal No. (Symbol) Terminal Description Condition Specified Condition
V7-6 (LIN) - Body ground LIN communication line Ignition switch ON Pulse generation