Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Communication stop for "Stop and Go/Start" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Engine stop and start ECU branch line or connector

·

Power source circuit of engine stop and start ECU

·

Engine stop and start ECU ground circuit

·

Engine stop and start ECU



WIRING DIAGRAM

C424515E01
0.083,1.281 0.979,1.594 0.896,0.313 10 false H97 0.438,1.281 3.052,1.708 2.615,0.427 10 false No. 11 Global CAN Junction Connector 1.542,0.26 2.76,0.458 1.219,0.198 10 false 10 1.542,0.781 2.646,0.99 1.104,0.208 10 false 21 5.271,0.354 5.729,0.552 0.458,0.198 10 false H66 5.271,0.885 5.729,1.083 0.458,0.198 10 false H66 5.271,1.719 5.729,1.917 0.458,0.198 10 false A33 5.281,2.292 5.74,2.49 0.458,0.198 10 false A33 5.281,2.844 5.74,3.042 0.458,0.198 10 false A34 5.281,5.073 5.74,5.271 0.458,0.198 10 false A33 5.271,5.563 5.729,5.76 0.458,0.198 10 false A33 5.667,5.563 6.156,5.823 0.49,0.26 10 false GND2 5.656,5.073 6.115,5.271 0.458,0.198 10 false GND1 5.677,4.49 6.135,4.688 0.458,0.198 10 false ACC 5.667,3.938 6.125,4.135 0.458,0.198 10 false IG2 5.667,3.385 6.125,3.583 0.458,0.198 10 false IG1 5.688,2.823 6.146,3.021 0.458,0.198 10 false +B 5.688,2.281 6.146,2.479 0.458,0.198 10 false BIN2 5.677,1.708 6.135,1.906 0.458,0.198 10 false BIN1 5.667,0.906 6.125,1.104 0.458,0.198 10 false CANL 5.656,0.365 6.115,0.563 0.458,0.198 10 false CANH 5.302,0.135 5.76,0.333 0.458,0.198 10 false 13 5.302,0.677 5.76,0.875 0.458,0.198 10 false 14 5.354,1.51 5.813,1.708 0.458,0.198 10 false 3 5.354,2.073 5.813,2.271 0.458,0.198 10 false 1 5.365,2.615 5.823,2.813 0.458,0.198 10 false 1 5.375,4.844 5.833,5.042 0.458,0.198 10 false 8 5.156,6.385 6.99,6.708 1.833,0.323 10 false Engine Stop and Start ECU 5.365,5.344 5.823,5.542 0.458,0.198 10 false 2 4.042,1.604 4.823,1.813 0.781,0.208 10 false BBC NO. 1 4.063,2.146 4.844,2.354 0.781,0.208 10 false BBC NO. 2 4.094,2.698 4.875,2.906 0.781,0.208 10 false EFI NO. 6 4.083,3.25 4.865,3.458 0.781,0.208 10 false EPS-IG1 3.99,3.813 4.948,4.052 0.958,0.24 10 false METER-IG2 4.063,4.375 5.031,4.594 0.969,0.219 10 false ECU-ACC 2.042,4.458 3.208,4.708 1.167,0.25 10 false from ACC Relay 1.75,3.906 3.26,4.281 1.51,0.375 10 false from IG2-NO. 2 Relay 1.729,3.344 3.198,3.635 1.469,0.292 10 false from IG1-NO. 1 Relay 1.74,2.813 3.51,3.198 1.771,0.385 10 false from EFI-MAIN Relay 2.292,2.24 3.479,2.542 1.188,0.302 10 false from Battery 2.281,1.667 3.49,1.906 1.208,0.24 10 false from Battery 5.323,3.167 5.781,3.365 0.458,0.198 10 false 21 5.281,3.406 5.74,3.604 0.458,0.198 10 false H66 5.333,3.729 5.792,3.927 0.458,0.198 10 false 18 5.292,3.948 5.75,4.146 0.458,0.198 10 false H66 5.323,4.292 5.781,4.49 0.458,0.198 10 false 19 5.281,4.5 5.74,4.698 0.458,0.198 10 false H66 5.271,6.042 5.729,6.24 0.458,0.198 10 false A34 5.375,5.854 5.833,6.052 0.458,0.198 10 false 6 5.677,6.031 6.26,6.271 0.583,0.24 10 false DGND

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ENGINE STOP AND START ECU BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C300830C24
1.51,0.094 2,0.406 0.49,0.313 0.729,1.823 0.844,1.823 0.844,1.823 0.781,1.406 true 1.344,1.813 1.167,1.813 1.167,1.813 0.917,1.406 true 0.188,0.146 0.5,0.302 0.313,0.156 10 false *a 1.635,0.177 1.99,0.333 0.354,0.156 10 false H66 0.333,1.74 0.74,1.885 0.406,0.146 10 false CANH 1.385,1.74 1.792,1.885 0.406,0.146 10 false CANL
*a Front view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the H66 engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H66-13 (CANH) - H66-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (ENGINE STOP AND START ECU)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the A33 and A34 engine stop and start ECU connectors.

C388157C14
0.844,0.417 1.281,0.688 0.438,0.271 3,0.427 3.438,0.698 0.438,0.271 5.552,0.438 5.99,0.708 0.438,0.271 1.667,2.167 1.469,2.167 1.469,2.167 1.469,1.667 true 5.438,1.719 5.438,2.167 5.438,2.167 5.146,2.167 true 5.563,1.719 5.563,2.458 5.563,2.458 5.281,2.458 true 0.552,1.25 0.552,0.802 0.552,0.802 0.406,0.802 true 0.552,1.667 0.552,2.177 0.552,2.177 0.406,2.177 true 1.635,0.813 1.469,0.813 1.469,0.813 1.469,1.25 true 2.333,0.927 2.208,0.927 2.208,0.927 2.208,1.396 true 2.979,0.927 2.792,0.927 2.792,0.927 2.792,1.375 true 6.198,2.417 6.031,2.417 6.031,2.417 6.031,1.719 true 0.938,0.458 1.396,0.656 0.458,0.198 10 false A33 3.104,0.469 3.563,0.667 0.458,0.198 10 false A34 5.656,0.49 6.115,0.729 0.458,0.24 10 false H66 1.719,2.083 2.333,2.281 0.615,0.198 10 false GND1 2.385,0.833 3,1.031 0.615,0.198 10 false +B 0.083,2.104 0.698,2.302 0.615,0.198 10 false BIN1 6.26,2.333 6.875,2.531 0.615,0.198 10 false IG1 0.073,0.719 0.688,0.917 0.615,0.198 10 false BIN2 4.896,2.073 5.51,2.271 0.615,0.198 10 false IG2 4.969,2.385 5.583,2.583 0.615,0.198 10 false ACC 1.688,0.729 2.302,0.927 0.615,0.198 10 false GND2 3.031,0.844 3.646,1.042 0.615,0.198 10 false DGND 0.115,0.104 0.427,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A33-2 (GND2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A33-8 (GND1) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
A34-6 (DGND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A33-1 (BIN2) - Body ground Always 9.5 to 14 V
A33-3 (BIN1) - Body ground Always 9.5 to 14 V
A34-1 (+B) - Body ground Ignition switch ON 9.5 to 14 V
H66-18 (IG2) - Body ground Ignition switch ON 9.5 to 14 V
H66-19 (ACC) - Body ground Ignition switch ACC 9.5 to 14 V
H66-21 (IG1) - Body ground Ignition switch ON 9.5 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)