Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (for Gasoline Model) › from 2020.11
RM37A0E _57 Power Source / Network _086883 NETWORKING _0417284 CAN COMMUNICATION SYSTEM(for Gasoline Model) J

NETWORKING  CAN COMMUNICATION SYSTEM(for Gasoline Model)  Headup Display Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Headup Display Communication Stop Mode Communication stop for "Head Up Display" is indicated on the "Communication Bus Check" screen of the GTS.
Click here(Click here)
·

Meter mirror sub-assembly branch line or connector

·

Power source circuit of meter mirror sub-assembly

·

Meter mirror sub-assembly ground circuit

·

Meter mirror sub-assembly



WIRING DIAGRAM

C424508E08
0.229,1.948 0.667,2.188 0.438,0.24 10 false H92 0.615,1.948 3.198,2.25 2.583,0.302 10 false No. 4 Global CAN Junction Connector 1.75,1.458 2.063,1.656 0.313,0.198 10 false 8 1.75,0.875 2.063,1.073 0.313,0.198 10 false 2 5.344,0.865 5.656,1.063 0.313,0.198 10 false 12 5.354,1.448 5.667,1.646 0.313,0.198 10 false 13 5.677,0.99 6.365,1.26 0.688,0.271 10 false MPX1 5.677,1.573 6.292,1.906 0.615,0.333 10 false MPX2 5.656,3.292 5.969,3.49 0.313,0.198 10 false B 5.427,3.167 5.74,3.365 0.313,0.198 10 false 2 3.969,3.135 5.167,3.448 1.198,0.313 10 false ECU-B NO. 2 2.156,3.271 3.365,3.635 1.208,0.365 10 false from Battery*2 1.583,2.448 3.323,2.885 1.74,0.438 10 false from IG1-NO. 1 Relay*2 3.885,2.333 5.156,2.646 1.271,0.313 10 false ECU-IG1 NO. 4 5.438,2.365 5.75,2.563 0.313,0.198 10 false 1 5.656,2.458 5.969,2.656 0.313,0.198 10 false IG 5.417,3.99 5.729,4.188 0.313,0.198 10 false 4 5.667,4.115 5.979,4.313 0.313,0.198 10 false ES 4.917,4.844 5.229,5.042 0.313,0.198 10 false H31 5.25,4.844 7.083,5.271 1.833,0.427 10 false Meter Mirror Sub-assembly 0.927,2.802 4.719,3.188 3.792,0.385 10 false from Engine Stop and Start ECU*1 0.938,3.625 4.729,4.01 3.792,0.385 10 false from Engine Stop and Start ECU*1 0.292,4.896 4.083,5.281 3.792,0.385 10 false *1: w/ Stop and Start System 0.292,5.292 4.083,5.677 3.792,0.385 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (METER MIRROR SUB-ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the H31 meter mirror sub-assembly connector.


c.
C380494C19
1.521,0.333 1.875,0.604 0.354,0.271 1.865,2.646 2.031,2.646 2.031,2.646 2.031,1.979 true 2.354,2.646 2.188,2.646 2.188,2.646 2.188,1.979 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.573,0.385 1.927,0.594 0.354,0.208 10 false H31 1.427,2.573 2.021,2.844 0.594,0.271 10 false MPX1 2.438,2.573 3.031,2.844 0.594,0.271 10 false MPX2
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H31-12 (MPX1) - H31-13 (MPX2) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (METER MIRROR SUB-ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C380494C20
1.521,0.333 1.875,0.604 0.354,0.271 2.906,0.802 2.74,0.802 2.74,0.802 2.74,1.635 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.583,0.385 1.896,0.583 0.313,0.198 10 false H31 2.99,0.719 3.302,0.948 0.313,0.229 10 false ES
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H31-4 (ES) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Result
OK
NG



OK

3.CHECK VEHICLE TYPE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/ Stop and Start System A
w/o Stop and Start System B



A

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.
C380494C21
1.521,0.333 1.875,0.604 0.354,0.271 0.531,0.813 0.698,0.813 0.698,0.813 0.698,1.646 true 1.177,0.802 1.01,0.802 1.01,0.802 1.01,1.635 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.583,0.385 1.896,0.583 0.313,0.198 10 false H31 0.313,0.74 0.906,1.01 0.594,0.271 10 false IG 1.271,0.719 1.865,0.99 0.594,0.271 10 false B
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H31-2 (B) - Body ground Always 11 to 14 V
H31-1 (IG) - Body ground Ignition switch ON 10.5 to 16 V



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

GO TO STOP AND START SYSTEM (FOR BACKUP BOOST CONVERTER CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Reconnect the cable to the negative (-) battery terminal.


b.
C380494C21
1.521,0.333 1.875,0.604 0.354,0.271 0.531,0.813 0.698,0.813 0.698,0.813 0.698,1.646 true 1.177,0.802 1.01,0.802 1.01,0.802 1.01,1.635 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.583,0.385 1.896,0.583 0.313,0.198 10 false H31 0.313,0.74 0.906,1.01 0.594,0.271 10 false IG 1.271,0.719 1.865,0.99 0.594,0.271 10 false B
*a Front view of wire harness connector
(to Meter Mirror Sub-assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H31-2 (B) - Body ground Always 11 to 14 V
H31-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

REPLACE METER MIRROR SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)