Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1621  Back Camera Power Supply Failure  


DESCRIPTION

This DTC is stored if the rear television camera assembly judges as a result of its self check that the signals or signal lines between the rear television camera assembly and parking assist ECU are not normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1621 Back Camera Power Supply Failure Rear television camera assembly power supply failure
·

Harness or connector

·

Rear television camera assembly

·

Parking assist ECU



WIRING DIAGRAM

E432780E05
1.625,0.469 1.99,0.688 0.365,0.219 10 false CB+ 1.521,1.281 2.25,1.479 0.729,0.198 10 false CGND 5.438,1.75 6.26,1.99 0.823,0.24 10 false H19 0.667,1.594 1.052,1.792 0.385,0.198 10 false W15 0.667,1.771 3,2.104 2.333,0.333 10 false Rear Television Camera Assembly 5.438,1.927 6.771,2.281 1.333,0.354 10 false Parking Assist ECU 5.594,0.458 6.052,0.656 0.458,0.198 10 false CB+ 5.594,1.26 6.052,1.458 0.458,0.198 10 false CGND 5.271,0.354 5.729,0.552 0.458,0.198 10 false 33 5.281,1.156 5.74,1.354 0.458,0.198 10 false 32 2.063,1.156 2.521,1.354 0.458,0.198 10 false 5 2.052,0.354 2.51,0.552 0.458,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly or multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the W15 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-33 (CB+) - W15-6 (CB+) Always Below 1 Ω
H19-32 (CGND) - W15-5 (CGND) Always Below 1 Ω
H19-33 (CB+) or W15-6 (CB+) - Body ground Always 10 kΩ or higher
H19-32 (CGND) or W15-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK PARKING ASSIST ECU (CB+, CGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK PARKING ASSIST ECU (CB+, CGND)
a.
E407111C20
1.417,0.25 1.917,0.5 0.5,0.25 1.438,1.146 1.208,1.906 1.208,1.906 0.958,1.906 true 1.51,1.156 1.979,1.948 1.979,1.948 2.229,1.948 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.646,1.823 1.115,2.021 0.469,0.198 10 false CB+ 1.542,0.292 2.042,0.448 0.5,0.156 10 false H19 2.271,1.865 2.833,2.052 0.563,0.188 10 false CGND
*a Component with harness connected
(Parking Assist ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-32 (CGND) - Body ground Always Below 1 Ω



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
H19-33 (CB+) - H19-32 (CGND) Ignition switch ON 5.5 to 7.05 V
H19-33 (CB+) - H19-32 (CGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG