This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1686 | Driver Side Camera Video Sync Signal Malfunction | Side camera feedback malfunction | ·
Harness or connector ·
Parking assist ECU ·
Side television camera assembly LH*1 ·
Side television camera assembly RH*2 ·
Outer rear view mirror assembly LH*1 ·
Outer rear view mirror assembly RH*2 |
*1: for LHD
*2: for RHD
When "!" is displayed on the radio and display receiver assembly or multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION
Clear the DTCs.
Check for DTCs.
DTC C1686 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for LHD | A |
| for RHD | B |
A
B
Disconnect the H19 parking assist ECU connector.
Disconnect the J29 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-12 (LCB+) - J29-3 (LCB+) | Always | Below 1 Ω |
| H19-10 (LCV+) - J29-5 (LCV+) | Always | Below 1 Ω |
| H19-34 (LCV-) - J29-4 (LCV-) | Always | Below 1 Ω |
| H19-35 (LGND) - J29-2 (LGND) | Always | Below 1 Ω |
| H19-11 (SGND) - J29-1 (SGND) | Always | Below 1 Ω |
| H19-12 (LCB+) or J29-3 (LCB+) - Body ground | Always | 10 kΩ or higher |
| H19-10 (LCV+) or J29-5 (LCV+) - Body ground | Always | 10 kΩ or higher |
| H19-34 (LCV-) or J29-4 (LCV-) - Body ground | Always | 10 kΩ or higher |
| H19-35 (LGND) or J29-2 (LGND) - Body ground | Always | 10 kΩ or higher |
| H19-11 (SGND) or J29-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H19 parking assist ECU connector.
| *a | Component without harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 35 (LGND) - Body ground | Always | Below 1 Ω |
| 34 (LCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-35 (LGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-12 (LCB+) - H19-35 (LGND) | Ignition switch ON | 5.5 to 7.05 V |
| H19-12 (LCB+) - H19-35 (LGND) | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly LH.
A waterproof connector is used for the side television camera assembly LH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly LH.
The video waveform is constantly output when the ignition switch is turned to ACC.
| Item | Content |
|---|---|
| Tester Connection | H19-10 (LCV+) - H19-35 (LGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, panoramic view monitor system operating |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Side Television Camera Assembly LH) |
| *b | Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH) |
Disconnect the outer rear view mirror assembly LH connector.
Disconnect the side television camera assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-1 (CB+) - J29-3 (LCB+) | Always | Below 1 Ω |
| A-3 (CV+) - J29-5 (LCV+) | Always | Below 1 Ω |
| A-7 (CV-) - J29-4 (LCV-) | Always | Below 1 Ω |
| A-5 (GND) - J29-2 (LGND) | Always | Below 1 Ω |
| A-1 (CB+) or J29-3 (LCB+) - Body ground | Always | 10 kΩ or higher |
| A-3 (CV+) or J29-5 (LCV+) - Body ground | Always | 10 kΩ or higher |
| A-7 (CV-) or J29-4 (LCV-) - Body ground | Always | 10 kΩ or higher |
| A-5 (GND) or J29-2 (LGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly LH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC C1686 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H19 parking assist ECU connector.
Disconnect the J13 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-40 (RCB+) - J13-3 (RCB+) | Always | Below 1 Ω |
| H19-38 (RCV+) - J13-5 (RCV+) | Always | Below 1 Ω |
| H19-16 (RCV-) - J13-4 (RCV-) | Always | Below 1 Ω |
| H19-17 (RGND) - J13-2 (RGND) | Always | Below 1 Ω |
| H19-39 (SGND) - J13-1 (SGND) | Always | Below 1 Ω |
| H19-40 (RCB+) or J13-3 (RCB+) - Body ground | Always | 10 kΩ or higher |
| H19-38 (RCV+) or J13-5 (RCV+) - Body ground | Always | 10 kΩ or higher |
| H19-16 (RCV-) or J13-4 (RCV-) - Body ground | Always | 10 kΩ or higher |
| H19-17 (RGND) or J13-2 (RGND) - Body ground | Always | 10 kΩ or higher |
| H19-39 (SGND) or J13-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H19 parking assist ECU connector.
| *a | Component without harness connected
(Parking Assist ECU) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 17 (RGND) - Body ground | Always | Below 1 Ω |
| 16 (RCV-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Parking Assist ECU) |
Remove the parking assist ECU with the connector still connected.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-17 (RGND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H19-40 (RCB+) - H19-17 (RGND) | Ignition switch ON | 5.5 to 7.05 V |
| H19-40 (RCB+) - H19-17 (RGND) | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the parking assist ECU with the connector still connected.
Using an oscilloscope, check the waveform of the side television camera assembly RH.
A waterproof connector is used for the side television camera assembly RH. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform 1 (camera lens not covered, displaying an image) |
| *c | Waveform 2 (camera lens covered, blacking out the screen) | *d | Synchronization Signal |
| *e | Video Waveform | - | - |
The video waveform changes according to the image sent by the side television camera assembly RH.
The video waveform is constantly output when the ignition switch is turned to ACC.
| Item | Content |
|---|---|
| Tester Connection | H19-38 (RCV+) - H19-17 (RGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | Ignition switch ON, panoramic view monitor system operating |
Waveform is similar to that shown in illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Side Television Camera Bssembly RH) |
| *b | Front view of wire harness connector
(to Outer Rear View Mirror Bssembly RH) |
Disconnect the side television camera assembly RH connector.
Disconnect the outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-1 (CB+) - J13-3 (RCB+) | Blways | Below 1 Ω |
| B-3 (CV+) - J13-5 (RCV+) | Blways | Below 1 Ω |
| B-7 (CV-) - J13-4 (RCV-) | Blways | Below 1 Ω |
| B-5 (GND) - J13-2 (RGND) | Blways | Below 1 Ω |
| B-1 (CB+) or J13-3 (RCB+) - Body ground | Blways | 10 kΩ or higher |
| B-3 (CV+) or J13-5 (RCV+) - Body ground | Blways | 10 kΩ or higher |
| B-7 (CV-) or J13-4 (RCV-) - Body ground | Blways | 10 kΩ or higher |
| B-5 (GND) or J13-2 (RGND) - Body ground | Blways | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the side television camera assembly RH with a new or normally functioning one.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Check for DTCs.
DTC C1683 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG