Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PANORAMIC VIEW MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0419518 PANORAMIC VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  PANORAMIC VIEW MONITOR SYSTEM  C1687  Over Current Detected in Driver Side Camera  


DESCRIPTION

This DTC is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the driver side television camera assembly to the parking assist ECU.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1687 Over Current Detected in Driver Side Camera Side camera current malfunction
·

Harness or connector

·

Parking assist ECU

·

Side television camera assembly LH*1

·

Side television camera assembly RH*2

·

Outer rear view mirror assembly LH*1

·

Outer rear view mirror assembly RH*2



*1: for LHD

*2: for RHD


WIRING DIAGRAM

for LHD
E407571E63
0.615,2.146 3.302,2.604 2.688,0.458 10 false Outer Rear View Mirror Assembly LH 0.5,1.979 1.417,2.177 0.917,0.198 10 false J29 5.688,1.521 6.604,1.719 0.917,0.198 10 false H19 5.74,1.698 7.083,1.958 1.344,0.26 10 false Parking Assist ECU 5.948,0.51 6.865,0.708 0.917,0.198 10 false LCB+ 5.938,0.979 6.854,1.177 0.917,0.198 10 false LGND 3.635,0.375 4.552,0.573 0.917,0.198 10 false LCB+ 3.594,0.813 4.51,1.01 0.917,0.198 10 false LGND 4.094,0.385 4.458,0.615 0.365,0.229 10 false 3 4.094,0.844 4.458,1.073 0.365,0.229 10 false 2 5.688,0.365 6.052,0.594 0.365,0.229 10 false 12 5.719,0.833 6.083,1.063 0.365,0.229 10 false 35 2.219,0.354 2.583,0.583 0.365,0.229 10 false 1 2.219,0.844 2.583,1.073 0.365,0.229 10 false 5 1.854,0.458 2.771,0.656 0.917,0.198 10 false CB+ 1.823,0.927 2.74,1.125 0.917,0.198 10 false GND 0.563,1.281 1.479,1.479 0.917,0.198 10 false A 0.708,1.417 3.396,1.875 2.688,0.458 10 false Side Television Camera Assembly LH

for RHD
E407571E62
0.844,2.156 3.302,2.469 2.458,0.313 10 false Outer Rear View Mirror Assembly RH 0.844,1.979 1.115,2.146 0.271,0.167 10 false J13 0.656,1.281 2.104,1.844 1.448,0.563 10 false Side Television Camera Assembly RH 3.615,0.344 4.021,0.552 0.406,0.208 10 false RCB+ 4.094,0.344 4.229,0.49 0.135,0.146 10 false 3 3.573,0.823 4.094,0.979 0.521,0.156 10 false RGND 4.083,0.823 4.396,0.969 0.313,0.146 10 false 2 5.698,1.698 7.156,2.177 1.458,0.479 10 false Parking Assist ECU 5.698,1.51 6.104,1.75 0.406,0.24 10 false H19 5.958,0.49 6.365,0.646 0.406,0.156 10 false RCB+ 5.927,0.958 6.427,1.146 0.5,0.188 10 false RGND 5.667,0.354 5.906,0.542 0.24,0.188 10 false 40 5.667,0.833 5.958,1.063 0.292,0.229 10 false 17 1.854,0.438 2.354,0.635 0.5,0.198 10 false CB+ 1.813,0.938 2.313,1.135 0.5,0.198 10 false GND 2.219,0.344 2.354,0.49 0.135,0.146 10 false 1 2.229,0.823 2.542,0.969 0.313,0.146 10 false 5 0.385,1.323 0.698,1.469 0.313,0.146 10 false B

CAUTION / NOTICE / HINT

NOTICE:
·

When "!" is displayed on the radio and display receiver assembly or multi-display assembly after the cable is disconnected from the negative (-) auxiliary battery terminal, correct the steering angle neutral point.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>INITIALIZATION

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK MODEL
2.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for LHD A
for RHD B




A

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LHRA ASSEMBLY LH)

B

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY LHRA ASSEMBLY LH)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the J29 outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-12 (LCB+) - J29-3 (LCB+) Always Below 1 Ω
H19-35 (LGND) - J29-2 (LGND) Always Below 1 Ω
H19-12 (LCB+) or J29-3 (LCB+) - Body ground Always 10 kΩ or higher
H19-35 (LGND) or J29-2 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK PARKING ASSIST ECU (LCB+, LGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK PARKING ASSIST ECU (LCB+, LGND)
a.
E402272C18
1.417,0.25 1.917,0.5 0.5,0.25 0.771,1.906 0.948,1.906 0.948,1.906 1.292,1.146 true 0.917,0.333 1,0.333 1,0.333 1.25,1 true 0.083,0.083 0.5,0.344 0.417,0.26 10 false *a 0.521,0.26 0.917,0.417 0.396,0.156 10 false LCB+ 0.365,1.823 0.979,1.969 0.615,0.146 10 false LGND 1.51,0.281 2.042,0.448 0.531,0.167 10 false H19
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-35 (LGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-12 (LCB+) - H19-35 (LGND) Ignition switch ON 5.5 to 7.05 V
H19-12 (LCB+) - H19-35 (LGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

NG

5.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
a.
E461714C12
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 2.292,1.781 2.042,1.781 2.042,1.781 1.719,2.521 true 2.271,3.167 2.021,3.167 2.021,3.167 1.906,2.688 true 2.458,0.292 3.073,0.49 0.615,0.198 10 false CB+ 2.479,1.354 3.094,1.552 0.615,0.198 10 false GND 2.396,1.698 3.01,1.896 0.615,0.198 10 false LCB+ 2.313,3.083 2.927,3.281 0.615,0.198 10 false LGND 0.833,0.875 1.448,1.073 0.615,0.198 10 false A 0.458,2.323 1.073,2.521 0.615,0.198 10 false J29 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly LH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly LH)


Disconnect the side television camera assembly LH connector.


b.

Disconnect the outer rear view mirror assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-1 (CB+) - J29-3 (LCB+) Always Below 1 Ω
A-5 (GND) - J29-2 (LGND) Always Below 1 Ω
A-1 (CB+) or J29-3 (LCB+) - Body ground Always 10 kΩ or higher
A-5 (GND) or J29-2 (LGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY LH

6.CHECK SIDE TELEVISION CAMERA ASSEMBLY LH
a.

Replace the side television camera assembly LH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1687 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY LH IS DEFECTIVE)

NG

8.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY RH)
a.

Disconnect the H19 parking assist ECU connector.


b.

Disconnect the J13 outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-40 (RCB+) - J13-3 (RCB+) Always Below 1 Ω
H19-17 (RGND) - J13-2 (RGND) Always Below 1 Ω
H19-40 (RCB+) or J13-3 (RCB+) - Body ground Always 10 kΩ or higher
H19-17 (RGND) or J13-2 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.CHECK PARKING ASSIST ECU (RCB+, RGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK PARKING ASSIST ECU (RCB+, RGND)
a.
E402272C16
1.417,0.25 1.917,0.5 0.5,0.25 0.5,1.771 0.677,1.771 0.677,1.771 0.865,1.156 true 0.667,0.333 0.833,0.333 0.833,0.333 0.938,0.99 true 0.083,0.042 0.5,0.302 0.417,0.26 10 false *a 0.198,0.25 0.76,0.448 0.563,0.198 10 false RGND 0.104,1.688 0.667,1.844 0.563,0.156 10 false RCB+ 1.542,0.302 2.042,0.458 0.5,0.156 10 false H19
*a Component with harness connected
(Parking Assist ECU)


Remove the parking assist ECU with the connector still connected.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H19-17 (RGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H19-40 (RCB+) - H19-17 (RGND) Ignition switch ON 5.5 to 7.05 V
H19-40 (RCB+) - H19-17 (RGND) Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

10.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

NG

10.INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
a.
E461714C20
0.646,0.833 1.146,1.083 0.5,0.25 0.323,2.281 0.823,2.531 0.5,0.25 2.406,0.365 2.156,0.365 2.156,0.365 1.979,0.75 true 2.438,1.427 2.188,1.427 2.188,1.427 2.01,1.073 true 2.292,1.781 2.042,1.781 2.042,1.781 1.719,2.521 true 2.271,3.167 2.021,3.167 2.021,3.167 1.906,2.688 true 2.458,0.292 3.073,0.49 0.615,0.198 10 false CB+ 2.521,1.354 3.135,1.552 0.615,0.198 10 false GND 2.396,1.698 3.01,1.896 0.615,0.198 10 false RCB+ 2.313,3.083 2.927,3.281 0.615,0.198 10 false RGND 0.833,0.875 1.448,1.073 0.615,0.198 10 false B 0.458,2.323 1.073,2.521 0.615,0.198 10 false J13 0.052,0.052 0.667,0.25 0.615,0.198 10 false *a 0.063,1.625 0.677,1.823 0.615,0.198 10 false *b
*a Front view of wire harness connector
(to Side Television Camera Assembly RH)
*b Front view of wire harness connector
(to Outer Rear View Mirror Assembly RH)


Disconnect the side television camera assembly RH connector.


b.

Disconnect the outer rear view mirror assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-1 (CB+) - J13-3 (RCB+) Always Below 1 Ω
B-5 (GND) - J13-2 (RGND) Always Below 1 Ω
B-1 (SCB+) or J13-3 (RCB+) - Body ground Always 10 kΩ or higher
B-5 (SGND) or J13-2 (RGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH

NG

REPLACE OUTER REAR VIEW MIRROR ASSEMBLY RH

11.REPLACE SIDE TELEVISION CAMERA ASSEMBLY RH
a.

Replace the side television camera assembly RH with a new or normally functioning one.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TELEVISION CAMERA (for Side)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
50002 353

b.

Check for DTCs.

Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
50001 353
OK:

DTC C1684 is not output.



Result:
Proceed to
OK
NG



OK

END (SIDE TELEVISION CAMERA ASSEMBLY RH IS DEFECTIVE)

NG