Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › PARKING ASSIST MONITOR SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086880 PARK ASSIST / MONITORING _0420014 PARKING ASSIST MONITOR SYSTEM Y

PARK ASSIST / MONITORING  PARKING ASSIST MONITOR SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the parking assist monitor system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.CUSTOMER PROBLEM ANALYSIS
2.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.

HINT:

The parking assist monitor display may be temporarily distorted due to radio waves around the vehicle.

Problem Symptom Cause
The problem symptom indicates a parking assist monitor display malfunction and the problem symptom cannot be reproduced. The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver.



Result:
Proceed to
NEXT



NEXT

3.INSPECT AUXILIARY BATTERY VOLTAGE
3.INSPECT AUXILIARY BATTERY VOLTAGE
a.

Measure the auxiliary battery voltage with the ignition switch off.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

4.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM
4.CHECK AUDIO AND VISUAL SYSTEM OR NAVIGATION SYSTEM

Result:
Result Proceed to
Audio and visual system or Navigation system is normal A
Audio and visual system or Navigation system is abnormal B



A

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*

B

5.CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM*
a.

Use the GTS to check if the CAN communication system is functioning normally.

for Gasoline model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for Gasoline Model)>DIAGNOSIS SYSTEM

for HV model: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for HV Model)>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

6.CHECK FOR DTC*

B

6.CHECK FOR DTC*
a.

Check for DTCs and make a note of any codes that are output.

Chassis > Rear Camera > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212

b.

Clear the DTCs.

Chassis > Rear Camera > Clear DTCs
50002 85
Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the detection conditions of the DTCs.

Chassis > Rear Camera > Trouble Codes
50001 85
Body Electrical > Navigation System > Trouble Codes
50001 212
NOTICE:

C1622 is output from the radio and display receiver assembly or multi-display assembly. Therefore, if C1622 is output, proceed to the Problem Symptoms Table for the relevant systems.

w/o Navigation System: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM>DIAGNOSTIC TROUBLE CODE CHART

w/ Navigation System for 12.3 Inch Display: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 12.3 Inch Display)>DIAGNOSTIC TROUBLE CODE CHART

w/ Navigation System for 8 Inch Display: Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>DIAGNOSTIC TROUBLE CODE CHART



Result:
Result Proceed to
No DTCs are output A
DTCs are output B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in Problem Symptoms Table A
Fault is listed in Problem Symptoms Table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END