Home › Audio / Visual / Telematics › AUDIO / VIDEO › REAR SEAT ENTERTAINMENT SYSTEM › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086877 AUDIO / VIDEO _0420185 REAR SEAT ENTERTAINMENT SYSTEM C

AUDIO / VIDEO  REAR SEAT ENTERTAINMENT SYSTEM  B15D5  Rear Seat Entertainment System Disconnected  


DESCRIPTION

The radio and display receiver assembly and television display assembly are connected by the AVC-LAN communication line.

This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and television display assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D5 Rear Seat Entertainment System Disconnected When either condition below is met:
·

The television display assembly is/was not connected while the ignition switch is/was ON or ACC

·

Communication between the master unit and the television display assembly is not possible when the engine*1 or hybrid system*2 is started


·

Television display assembly power source circuit

·

AVC-LAN circuit between master unit and television display assembly

·

Television display assembly

·

Radio and display receiver assembly

·

Harness or connector

·

Stop and start system*3



*1: for Gasoline Model

*2: for HV Model

*3: w/ Stop and Start System


HINT:

The radio and display receiver assembly is the master unit.


WIRING DIAGRAM

E436453E04
1.135,4.313 3.156,4.51 2.021,0.198 10 false : AVC-LAN Communication Line 2.333,0.385 4.354,0.583 2.021,0.198 10 false from Auxiliary Battery*1 2.677,1.302 4.698,1.5 2.021,0.198 10 false from ACC Relay*1 4.49,0.542 5.26,0.74 0.771,0.198 10 false RADIO 4.385,1.438 5.156,1.635 0.771,0.198 10 false ECU-ACC 5.604,3.271 6.063,3.469 0.458,0.198 10 false GND 5.604,2.74 6.063,2.938 0.458,0.198 10 false TX1- 5.604,2.365 6.063,2.563 0.458,0.198 10 false TX1+ 5.604,1.302 6.063,1.5 0.458,0.198 10 false ACC 5.604,0.396 6.063,0.594 0.458,0.198 10 false +B 3.708,2.354 4.167,2.552 0.458,0.198 10 false TX+ 3.719,2.708 4.177,2.906 0.458,0.198 10 false TX- 5.354,3.615 5.667,3.813 0.313,0.198 10 false R16 5.344,3.823 7.156,4.042 1.813,0.219 10 false Television Display Assembly 2.906,3.021 3.219,3.219 0.313,0.198 10 false H1 2.896,3.198 4.573,3.552 1.677,0.354 10 false Radio and Display Receiver Assembly 4.021,2.229 4.479,2.427 0.458,0.198 10 false 19 4.031,2.604 4.49,2.802 0.458,0.198 10 false 20 5.417,0.292 5.875,0.49 0.458,0.198 10 false 1 5.417,1.167 5.875,1.365 0.458,0.198 10 false 2 5.427,2.208 5.885,2.406 0.458,0.198 10 false 4 5.427,2.594 5.885,2.792 0.458,0.198 10 false 5 5.344,3.146 5.76,3.365 0.417,0.219 10 false 17 0.865,3.917 3.438,4.146 2.573,0.229 10 false *2: w/ Stop and Start System 0.854,3.552 3.427,3.781 2.573,0.229 10 false *1: w/o Stop and Start System 2.146,0.885 4.375,1.104 2.229,0.219 10 false from Engine Stop and Start ECU*2 2.156,1.771 4.385,1.99 2.229,0.219 10 false from Engine Stop and Start ECU*2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Check that optional components (including associated wiring) which generate radio waves are not installed.

Result:
Result Proceed to
Optional components (including associated wiring) are installed. A
Optional components (including associated wiring) are not installed. B


HINT:
·

Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

·

This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.





A

2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)

B

3.CHECK DTC
2.REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
a.

Remove optional components (including associated wiring).

NOTICE:

Do not remove optional components or associated wiring without the permission of the customer.



Result:
Proceed to
NEXT



NEXT

3.CHECK DTC
3.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)
4.CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY POWER SOURCE)
a.

Disconnect the R16 television display assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-17 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition

*1: for Gasoline Model

*2: for HV Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System

R16-1 (+B) - R16-17 (GND) Always*1
Ignition switch off*2
11 to 14 V*3
10.5 to 16 V*4
R16-2 (ACC) - R16-17 (GND) Ignition switch ACC 11 to 14 V*3
10.5 to 16 V*4



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
a.

Disconnect the H1 radio and display receiver assembly connector.


b.

Disconnect the R16 television display assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R16-4 (TX1+) - H1-19 (TX+) Always Below 1 Ω
R16-5 (TX1-) - H1-20 (TX-) Always Below 1 Ω
R16-4 (TX1+) or H1-19 (TX+) - Body ground Always 10 kΩ or higher
R16-5 (TX1-) or H1-20 (TX-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.REPLACE TELEVISION DISPLAY ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.REPLACE TELEVISION DISPLAY ASSEMBLY
a.

Replace the television display assembly with a new or known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEVISION DISPLAY>REMOVAL


b.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

c.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (TELEVISION DISPLAY ASSEMBLY WAS DEFECTIVE)

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY