When the shift lever is in S, different ranges can be chosen using the floor shift sequential gate.
Refer to the wiring diagram for the Shift Paddle Switch Circuit.
Read the Data List using the GTS.
| Tester Display |
|---|
| Sports Shift Position |
| Result | Proceed to |
|---|---|
| GTS display changes according to shift lever operation | A |
| GTS display does not change according to shift lever operation | B |
Turn the ignition switch off.
A
B
Read the Data List using the GTS.
| Tester Display |
|---|
| Sports Shift UP Signal |
| Sports Shift DOWN Signal |
| Result | Proceed to |
|---|---|
| GTS display changes according to transmission control switch operation | A |
| GTS display does not change according to transmission control switch operation | B |
Turn the ignition switch off.
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H29 transmission control switch (shift lock control unit assembly) connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Transmission Control Switch (Shift Lock Control Unit Assembly)) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H29-4 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
Turn the ignition switch off.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H29-4 (IG) - Body ground | Ignition switch off | Below 1 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H29-2 (E) - Body ground | Ignition switch off | Below 1 Ω |
Reconnect the H29 transmission control switch (shift lock control unit assembly) connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>P810 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H67 hybrid vehicle control ECU connector.
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-25 (M) - Body ground | Ignition switch ON
Shift lever in S, "+" or "-" |
11 to 14 V |
| Ignition switch ON
Except shift lever in S, "+" and "-" |
Below 1 V |
If the ignition switch is turned to ON with the hybrid vehicle control ECU connector disconnected, other DTCs will be stored. After performing the inspection, clear the DTCs.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| H67-24 (SFTU) - Body ground | Shift lever in S | 10 kΩ or higher |
| H67-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| H67-11 (SFTD) - Body ground | Shift lever in S | 10 kΩ or higher |
Reconnect the H67 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereDrivetrain>P810 (HYBRID TRANSMISSION / TRANSAXLE)>SHIFT LEVER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H67 hybrid vehicle control ECU connector.
| *a | Front view of wire harness connector
(to Hybrid Vehicle Control ECU) |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-24 (SFTU) - Body ground | Shift lever held in "+" | Below 1 Ω |
| H67-24 (SFTU) - Body ground | Shift lever in S | 10 kΩ or higher |
| H67-11 (SFTD) - Body ground | Shift lever held in "-" | Below 1 Ω |
| H67-11 (SFTD) - Body ground | Shift lever in S | 10 kΩ or higher |
Reconnect the H67 hybrid vehicle control ECU connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG