The immobiliser function compares the ID code that is registered in the certification ECU (smart key ECU assembly) with the ID code of the transponder chip that is embedded in the electrical key transmitter sub-assembly.
When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to Diagnostic Trouble Code Chart.
Before replacing the ECM, certification ECU (smart key ECU assembly) or ID code box (immobiliser code ECU)*, refer to Service Bulletin.
*: w/ ID Code Box
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
If an immobiliser function or SFI system DTC is output, first perform troubleshooting for the immobiliser function or SFI system DTC.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut Status | Status of immobiliser fuel cut | OFF or ON | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut Status |
OFF is displayed after the engine is started.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>2GR-FKS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check that the engine starts 5 seconds after the ignition switch turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/ ID Code Box) | B |
| NG (w/o ID Code Box) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the H53 ID code box (immobiliser code ECU) connector.
Disconnect the A28 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H53-3 (EFII) - A28-45 (IMO) | Always | Below 1 Ω |
| H53-3 (EFII) or A28-45 (IMO) - Other terminals and body ground | Always | 10 kΩ or higher |
| H53-4 (EFIO) - A28-59 (IMI) | Always | Below 1 Ω |
| H53-4 (EFIO) or A28-59 (IMI) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H53 ID code box (immobiliser code ECU) connector.
Connect the A28 ECM connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(ID Code Box (Immobiliser Code ECU)) |
*b | Approximately 160 ms. |
| *c | Approximately 270 ms. | *d | Approximately 40 ms. |
| *e | Approximately 60 ms. | *f | Waveform (EFII) |
| *g | Waveform (EFIO) | *h | Waveform A |
| *i | Waveform B | *j | Waveform C |
| *k | Waveform A (detail) | - | - |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| H53-3 (EFII) - Body ground | Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform (EFII)) |
| H53-4 (EFIO) - Body ground | Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform (EFIO)) |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A or C not output, or has abnormal wavelength or shape | B |
| Waveform B not output, or has abnormal wavelength or shape | C |
A
B
C
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the engine starts.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A19 certification ECU (smart key ECU assembly) connector.
Disconnect the A28 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A19-3 (EFII) - A28-45 (IMO) | Always | Below 1 Ω |
| A19-3 (EFII) or A28-45 (IMO) - Other terminals and body ground | Always | 10 kΩ or higher |
| A19-4 (EFIO) - A28-59 (IMI) | Always | Below 1 Ω |
| A19-4 (EFIO) or A28-59 (IMI) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the A19 certification ECU (smart key ECU assembly) connector.
Connect the A28 ECM connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
*b | Approximately 160 ms. |
| *c | Approximately 270 ms. | *d | Approximately 40 ms. |
| *e | Approximately 60 ms. | *f | Waveform (EFII) |
| *g | Waveform (EFIO) | *h | Waveform A |
| *i | Waveform B | *j | Waveform C |
| *k | Waveform A (detail) | - | - |
The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| A19-3 (EFII) - Body ground | Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform (EFII)) |
| A19-4 (EFIO) - Body ground | Within 3 seconds of engine start or within 3 seconds of ignition switch turned to ON after battery cable disconnected and reconnected | 2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform (EFIO)) |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform A or C not output, or has abnormal wavelength or shape | B |
| Waveform B not output, or has abnormal wavelength or shape | C |
A
B
C
Register the ECU communication ID.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Check that the engine starts.
Engine starts normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG