Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM (for 8 Inch Display) › from 2020.11
RM37A0E _56 Audio / Visual / Telematics _086878 NAVIGATION / MULTI INFO DISPLAY _0418790 NAVIGATION SYSTEM(for 8 Inch Display) C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for 8 Inch Display)  B158F  AV Signal Stoppage (Low Battery Voltage)  


DESCRIPTION

This DTC is stored when a video or audio signal is interrupted due to auxiliary battery voltage input to the radio and display receiver assembly dropping temporarily.

DTC No. Detection Item DTC Detection Condition Trouble Area
B158F AV Signal Stoppage (Low Battery Voltage) A video or audio signal is interrupted when the auxiliary battery voltage drops
·

Radio and display receiver assembly

·

Harness or connector

·

Stop and start system*



*: w/ Stop and Start System


WIRING DIAGRAM

E309491E49
5.271,1.031 5.729,1.229 0.458,0.198 10 false +B1 5.052,0.906 5.25,1.104 0.198,0.198 10 false 4 5.031,1.906 5.49,2.104 0.458,0.198 10 false H1 5.031,2.083 6.229,2.51 1.198,0.427 10 false Radio and Display Receiver Assembly 3.104,1.177 4.292,1.531 1.188,0.354 10 false RADIO NO. 2 0.167,1.021 2.281,1.49 2.115,0.469 10 false from Auxiliary Battery*1 0.594,1.417 2.76,1.625 2.167,0.208 10 false from Engine Stop and Start ECU*2 0.26,2.031 2.427,2.24 2.167,0.208 10 false *1: w/o Stop and Start System 0.26,2.365 2.427,2.573 2.167,0.208 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E268487

Enter the "Vehicle Signal Check Mode" screen. Refer to Check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM (for 8 Inch Display)>OPERATION CHECK


b.

Measure the auxiliary battery voltage.

Standard Voltage:

11 to 14 V (w/o Stop and Start System)

10.5 to 16 V (w/ Stop and Start System)


HINT:

This display is updated once per second.



Result:
Proceed to
OK
NG



OK

2.CHECK DTC

NG

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
2.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY POWER SOURCE)
a.

Disconnect the H1 radio and display receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H1-4 (+B1) - Body ground*1 Ignition switch off 11 to 14 V
H1-4 (+B1) - Body ground*2 Always 11 to 14 V*3
10.5 to 16 V*4


*1: for HV Model

*2: for Gasoline Model

*3: w/o Stop and Start System

*4: w/ Stop and Start System



Result:
Result Proceed to
OK A
NG (w/o Stop and Start System) B
NG (w/ Stop and Start System) C



A

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C