Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › 2020.11–2021.10
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS, A25B-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS, A25B-FXS ENGINE CONTROL  SFI SYSTEM  P05A27E  Active Grille Air Shutter "A" Actuator Stuck On  P05A27F  Active Grille Air Shutter "A" Actuator Stuck Off  


DESCRIPTION

Refer to DTC P059F73.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>P059F73

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P05A27E Active Grille Air Shutter "A" Actuator Stuck On The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·

Grille shutter opening operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more.


·

Radiator shutter sub-assembly

·

Swing grille actuator assembly


Does not come on DTC stored SAE Code: P05A3
P05A27F Active Grille Air Shutter "A" Actuator Stuck Off The following condition is met and the ECM receives a malfunction signal 17 times* (2 trip detection logic):
·

Grille shutter closing operation is performed for 11 seconds or more and the ECM receives a malfunction signal once or more.


·

Radiator shutter sub-assembly

·

Swing grille actuator assembly


Does not come on DTC stored SAE Code: P05A3

HINT:

*: For every 65 ms that the ECM receives a grille shutter system malfunction signal from the grille shutter ECU (swing grille actuator assembly) the ECM determines it has received the signal 1 time. If the ECM determines the malfunction signal has been received 17 consecutive times (the signal is received for approximately 1 second continuously), it will store a DTC.


MONITOR DESCRIPTION

If the grille shutter ECU (swing grille actuator assembly) detects that the grille shutter motor (swing grille actuator assembly) is performing an open or close operation for longer than the threshold, it will output a malfunction signal to the ECM and the ECM will store a DTC.

Detection Condition DTC No.
Opening Operation P05A27E (Active Grille Air Shutter "A" Actuator Stuck On)
Closing Operation P05A27F (Active Grille Air Shutter "A" Actuator Stuck Off)

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Enter the following menus: Body Electrical / Grille Shutter / Utility / Grille Shutter Control Mode Switching.

9.

According to the display on the GTS, change the Grillee shutter control mode from normal mode to maintenance mode.

10.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Closing Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

11.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.


12.

Enter the following menus: Body Electrical / Grille Shutter / Active Test / Shutter Opening Operation Lock Detection / Data List / Shutter Operation Lock Detection Result for Active Test.

13.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

OK:

"Normal" is displayed.



CAUTION / NOTICE / HINT

NOTICE:
·

In order to ensure safety, before performing troubleshooting or removing the swing grille actuator assembly or radiator shutter sub-assembly, change the grille shutter control mode to maintenance mode.

·

Vehicle Control History may be stored in the hybrid vehicle control ECU assembly if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the freeze frame data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU assembly, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY



HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
a.

According to the display on the GTS, change the grille shutter control mode from normal mode to maintenance mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grille Shutter Control Mode Switching
50005 352 4221

Result:
Proceed to
NEXT



NEXT

2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
2.INSPECT GRILLE SHUTTER (FOREIGN MATTER AND ICE)
a.

Check the area around the shutters and the links of the grille shutter for foreign matter and ice.

OK:

No foreign matter or ice.



Result:
Proceed to
OK
NG



OK

3.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)

NG

8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
3.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
a.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Closing Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 3 8
OK:

"Normal" is displayed.



b.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Opening Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 4 8
OK:

"Normal" is displayed.



HINT:

When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.


Result:
Proceed to
OK
NG



OK

4.CLEAR DTC

NG

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
4.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

5.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
5.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

b.

Check for DTCs and make sure that DTC B1333 is not output.

Body Electrical > Grill Shutter > Trouble Codes
50001 352

Result:
Proceed to
NEXT



NEXT

END

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
a.

Remove the radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

Remove the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


c.

Reconnect the swing grille actuator assembly connector.


d.

According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

Body Electrical > Grill Shutter > Active Test
Tester Display
Shutter Closing Operation Lock Detection
50004 352 3
OK:

Operation is normal.



e.

According to the display on the GTS, perform the Active Test and check the operation of the swing grille actuator assembly.

Body Electrical > Grill Shutter > Active Test
Tester Display
Shutter Opening Operation Lock Detection
50004 352 4
OK:

Operation is normal.



HINT:

Perform "Grille Shutter Control Mode Switching and Grille Shutter Initialization" after replacing the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

7.INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION)

NG

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

7.INSPECT RADIATOR SHUTTER SUB-ASSEMBLY (GRILLE SHUTTER OPERATION)
a.

Remove the radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>REMOVAL


b.

Remove the swing grille actuator assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER>DISASSEMBLY


c.

Manually open and close the radiator shutter sub-assembly and check that it moves smoothly.

OK:

Radiator shutter sub-assembly moves smoothly.



HINT:

Perform "Grille Shutter Control Mode Switching and Grille Shutter Initialization" after replacing the swing grille actuator assembly or radiator shutter sub-assembly.

Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>GRILLE SHUTTER SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE SWING GRILLE ACTUATOR ASSEMBLY

NG

REPLACE RADIATOR SHUTTER SUB-ASSEMBLY

8.REMOVE FOREIGN MATTER OR ICE (CLEAN GRILLE SHUTTER)
a.

Remove any foreign matter and/or ice from the area around the shutters and the links of the grille shutter.


Result:
Proceed to
NEXT



NEXT

9.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
9.PERFORM ACTIVE TEST USING GTS (GRILLE SHUTTER OPERATION)
a.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Closing Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 3 8
OK:

"Normal" is displayed.



b.

According to the display on the GTS, perform the Active Test and read the value of Data List item Shutter Operation Lock Detection Result for Active Test.

Body Electrical > Grill Shutter > Active Test
Active Test Display
Shutter Opening Operation Lock Detection
Data List Display
Shutter Operation Lock Detection Result for Active Test
50004 352 4 8
OK:

"Normal" is displayed.



HINT:

When the value of Data List item Shutter Operation Lock Detection Result for Active Test is "Normal", it can be determined that the grille shutter system has returned to normal.


Result:
Proceed to
OK
NG



OK

10.CLEAR DTC

NG

6.PERFORM ACTIVE TEST USING GTS (SWING GRILLE ACTUATOR ASSEMBLY OPERATION)
10.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

11.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
11.PERFORM UTILITY USING GTS (GRILLE SHUTTER CONTROL MODE SWITCHING)
a.

According to the display on the GTS, change the grille shutter control mode from maintenance mode to normal mode.

Body Electrical > Grill Shutter > Utility
Tester Display
Grill Shutter Control Mode Switching
50005 352 4221

b.

Check for DTCs and make sure that DTC B1333 is not output.

Body Electrical > Grill Shutter > Trouble Codes
50001 352

Result:
Proceed to
NEXT



NEXT

END