Home › Engine / Hybrid System › A25A-FXS, A25B-FXS (ENGINE CONTROL) › SFI SYSTEM › from 2020.11
RM37A0E _51 Engine / Hybrid System _086905 A25A-FXS, A25B-FXS ENGINE CONTROL _0419404 SFI SYSTEM C

A25A-FXS, A25B-FXS ENGINE CONTROL  SFI SYSTEM  P246300  Particulate Filter Restriction - Soot Accumulation Bank 1  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P246300 Particulate Filter Restriction - Soot Accumulation Bank 1 During high load operation, the PM (Particulate Matter) accumulation ratio is 68% or higher for 1 second or more (1 trip detection logic). Front exhaust pipe assembly (GPF) Comes on DTC stored SAE Code: P2463

MONITOR DESCRIPTION

When the accumulation ratio of the PM in the GPF (Gasoline Particulate Filter) is at the specified value or higher, output is limited during high load operation to prevent the GPF from rising to a high temperature. A DTC is stored at this time.

The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A435819E10
3.771,3.25 3.625,3.25 3.625,3.25 3.458,2.885 false 6.094,3.25 6.219,3.25 6.219,3.25 6.375,2.885 false 2.292,3.417 2.417,3.417 2.417,3.417 2.552,2.885 false 0.396,2.396 1.813,2.625 1.417,0.229 10 false Ignition switch ON 0.458,2.677 1.615,2.865 1.156,0.188 10 false Ignition switch off 1.167,2.115 2.083,2.313 0.917,0.198 10 false Idling 0.052,1.167 1.729,1.354 1.677,0.188 10 false 60 km/h [Engine running] 1.958,2.01 2.281,2.281 0.323,0.271 10 false [A] 2.917,2 3.26,2.25 0.344,0.25 10 false [B] 2.708,2.99 3.344,3.375 0.635,0.385 10 false 5 minutes or more 3.833,3.167 4.771,3.448 0.938,0.281 10 false 30 seconds 5.365,3.167 6.208,3.448 0.844,0.281 10 false 30 seconds 6.844,3.125 7.125,3.427 0.281,0.302 10 false [D] 3.604,1.406 3.885,1.708 0.281,0.302 10 false [C] 1.656,2.99 2.458,3.406 0.802,0.417 10 false Warming up 1.573,3.323 2.417,3.604 0.844,0.281 10 false 30 seconds

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) [A].

7.

Turn the ignition switch off and wait for at least 30 seconds.

8.

Turn the ignition switch to ON.

9.

Turn the GTS on.

10.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

11.

Start the engine and idle it for 5 minutes or more [B].

12.

Turn the ignition switch off and wait for at least 30 seconds.

13.

Turn the ignition switch to ON.

14.

Turn the GTS on.

15.

Put the engine in Inspection Mode (Maintenance Mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

16.

With the engine running, repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) and then decelerating the vehicle 5 times [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

If the engine stops, further depress the accelerator pedal to restart the engine.


17.

Turn the ignition switch off and wait for at least 30 seconds.

18.

Turn the ignition switch to ON.

19.

Turn the GTS on.

20.

Enter the following menus: Powertrain / Engine / Trouble Codes [D].

21.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



22.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

23.

Input the DTC: P246300.

24.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [D] again.



25.

Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.

26.

Read the value displayed on the GTS.

HINT:
·

If the PM Deposition Ratio value is less than 68%, the system is normal.

·

If the PM Deposition Ratio value is 68% or higher, perform forced particulate filter regeneration.




CAUTION / NOTICE / HINT

HINT:
·

Clear the Vehicle Control History after completing repairs.

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY

·

If the PM deposition amount is extremely high, an abnormal noise (rattling) may be heard from the vicinity of the hybrid vehicle transaxle, but this is not a malfunction of the hybrid vehicle transaxle. Performing forced particulate filter regeneration to eliminate the over-deposition will cause the noise to stop.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



NOTICE:
·

Vehicle Control History may be stored in the hybrid vehicle control ECU if the engine is malfunctioning. Certain vehicle condition information is recorded when Vehicle Control History is stored. Reading the vehicle conditions recorded in both the Freeze Frame Data and Vehicle Control History can be useful for troubleshooting.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY

(Select Powertrain in Health Check and then check the time stamp data.)

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR

·

If any "Engine Malfunction" Vehicle Control History item has been stored in the hybrid vehicle control ECU, make sure to clear it. However, as all Vehicle Control History items are cleared simultaneously, if any Vehicle Control History items other than "Engine Malfunction" are stored, make sure to perform any troubleshooting for them before clearing Vehicle Control History.

Click hereEngine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM (for 4WD/AWD)>VEHICLE CONTROL HISTORY



PROCEDURE

1.READ VALUE USING GTS (ASH DEPOSITION RATIO)
a.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Ash Deposition Ratio Bank1
50003 372 822
Standard:
GTS Display Specified Condition
Ash Deposition Ratio Bank1 Less than 100%



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

5.REPLACE FRONT EXHAUST PIPE ASSEMBLY
2.CLEAR DTC
a.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

b.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CLEAR VEHICLE CONTROL HISTORY
3.CLEAR VEHICLE CONTROL HISTORY
a.

Clear the Vehicle Control History.

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.



Result:
Proceed to
NEXT



NEXT

4.PERFORM PM REGENERATE MODE
4.PERFORM PM REGENERATE MODE

NEXT

END

5.REPLACE FRONT EXHAUST PIPE ASSEMBLY

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (INTAKE / EXHAUST)>EXHAUST PIPE>REMOVAL

HINT:

Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly (GPF).

Click hereEngine / Hybrid System>A25A-FXS, A25B-FXS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
NEXT



NEXT

6.CLEAR VEHICLE CONTROL HISTORY
6.CLEAR VEHICLE CONTROL HISTORY
a.

Clear the Vehicle Control History.

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.



Result:
Proceed to
NEXT



NEXT

END